5-37. A 300-kg counterweight, with center of mass at G, ismounted on the pitman crank AB of the oil-pumping unit.If the motor supplies a torque of M - 2500 N- m, determinethe force F developed in the fixed cable attached to the endof the walking beam DEF.-1.75 m--2.50 m3005 m0.65 m

Given Counterweight = 300 kg Torque = 2500 Nm To find Force in the fixed cable

Answered: 5-37. A 300-kg counterweight, with…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? Answers: M= A Ax= i i -2.4° 170 lb L--x -2.4 B M 1.9' 64° lb-ft lb 1.9' C
A force of 1000 lb is applied to the 600-lb horizontal beam supported by a hinge at A and a roller at B on a smooth surface. If the pin support at A suddenly fails, calculate the magnitude of the force of the roller at B acting on the beam at that instant, by modelling the beam as a uniform slender bar. Present your answer in lb using 3 significant figures. 4 13 1000 lb -8 ft- B -2 ft-
Determine the magnitude of the horizontal force F and the support reactions at pin A.If the cord CB can sustain a maximum load of 1500N.
The bobcat loader (Figure Q3) has a mass of 1200-kg, shows the center of mass is at G1. If there is a 200-kg pebble in the bucket, with center of mass at G2 determine the reactions of each pair of wheels A and B on the ground and the force in the hydraulic cylinder CD and at the pin E. There is a similar linkage on each side of the loader. L0.5 m E 0.1 m_ D 0.2 m G2 0.18 m G1 0.6 m 0.5 m В 0.45 m 1.2 m 0.15 m 0.2 m 0.05 m Figure Q3
A spring with squared and ground ends has 16 active coils diameter of 6 mm and pitch of 10 mm . If spring rate is 85 KN/m , determine the solid force?
It is desired to balance the rotor shown in the figure by placing balancing masses at a distance of ei and Li mm from the rotation axis in the R and L balancing planes. Find the balancing masses and their angular positions to be used in balancing. in the tableUse the given values.Find the L and R support reactions.
6-76 The triangular plate of uniform thickness shown in Fig. the two cables supporting the plate and the reaction at the ball support. has a mass of 400 kg. Determine the tensions in 900 mm B 1500 mm y
Pin A, which connects the 200-kg steel beam with the center of gravity at G to the vertical column, is welded both to the beam and to the column. To test the weld, the 70-kg man loads the beam by exerting a 300-N force on the rope which passes through a hole in the beam as shown. Calculate the moment supported by the pin. Express your answer in units of kN-m. A Welded pin 1200 mm Go -600 mm 300 mm
draw the free diagram of the wheel and member abc used as part of the landing gear on a jet plane. the hydraulic cylinder ad acts as a two force member, and there is a pin connection at b
The structure is comprised of rigid bars AB and BCD supported by hinges at A and D. A steel rod at C provides additional support to the system. As shown, there is a roller connection between the bars at B. Determine the magnitude of the force P applied as shown if the vertical displacement of point B is limited to 1.5 mm. Neglect the weights of the bars.
Problem Statement Based on Problem 4-59 from the textbook. The board is used to hold the end of the cross lug wrench in the position shown. If a torque of 30 N*m about x axis is required to tighten the nut, determine the required magnitude of the force F needed to turn the wrench. Force F lies in a verticla plane. = 280 mm b=235 mm -Fach Student: b Z 60° a - y
Determine the support reactions: 4 m 4 m 150 KN 6 m 25 kN/m -10 m- Diag 4m T 4m Ax ISC

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

5-37. A 300-kg counterweight, with center of mass at G, is mounted on the pitman crank AB of the oil-pumping unit. If the motor supplies a torque of M - 2500 N- m, determine the force F developed in the fixed cable attached to the end of the walking beam DEF. -1.75 m- -2.50 m 30 05 m 0.65 m