5-2. Determine the load in each member of the truss shown in Figure P5-2. B 5 KN 3 m A 2.5 m 2 m D 4 m FIGURE P5-2

Q: A jet airplane touches down on an airport runway with a speed of 213 km/hr. It slows at a constant…

A: Given ,         initial speed = 213 kmhr                       u = 213x518ms…

Q: A counter balance valve is not used for always flow retardation continuously, and resists its flow…

A: Required : True or False.

Q: What is Daltons law of partial pressure?

A: The Dalton law of partial pressure states that the total pressure exerted by a mixture of gases is…

Q: Why do animals curl into ball during winter?

A: The expression for the heat liberated from the body is,

Q: Write a report on the flaps used at the leading and trailing edges of the wings of large commercial…

A:

Q: A piece of silver weighing 685g in air weighs 437g when immersed in glycerine whose SG is 1.25.…

A: Silver m= 685g in air  437 g in glycerine  Specific gravity is 1.25  Densit(pgl) = 1250kg/m3

Q: Determine the minimum cylinder mass m1 required to cause loss of contact at A.

A: Given that: To determine the minimum mass of m1 so that there is a loss of contact at A.

Q: Does the (a) efficiency and (b) effectiveness of a fin increase or decrease as the fin length is…

A: (a) The fin efficiency is given as the ratio of the heat transfer to the fin to the heat transfer to…

Q: For a one-component system under conditions of constant pressure, how many phases can normally be at…

A: Given: The number of components of the system is C = 1

Q: Why is a liquid container more likely to burst from the base?

A: One is that air pressure is which causing the bottom to break out.

Q: Why is rifle bullet made cylindrical?

A: A rifle bullet is not completely cylindrical. It is a combination of cone and cylinder.

Q: wt) + P13.13 Does the superposition (x, t) = sin(kx 2A sin(kx + wt) generate a standing wave? Answer…

A:

Q: Match the motion map to the correct graph.

A: 1.  The car is moving towards left Which means its velocity is negative. The distance between all…

Q: QUESTION 7 Q4 (d.)What is the major differences between the stacking and separating gels? For the…

A:

Q: The swept area of wind turbines is increased by a factor 4, by doubling the blade length. Prove the…

A:

Q: Figure below shows the cross-sectional area of a beam; the first moment of area about the axes A - A…

A: Consider the section of the left side of the axis A-A is section 1 and the right side section of the…

Q: Freddie the fish shines his flashlight upward from under water.If Freddie shines his flashlight at…

A:

Q: the pascal pa unit of pressure is writter as?

A:

Q: A uniform rod, 110 cm in length, is pivoted at the 40 cm mark. It is balanced when a…

A: Visualize the problem:

Q: We have a light pole given below. -Assume the weight of the lamp is 200kg.(concentrated load) and…

A: Given: Weight of the lamp (w) = 200 kg Distance between Centre of gravity to pole Centre = 2m  wind…

Q: 4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the…

A: inlet velocity=40 m/s mass flow rate=1000 kg /s Energy flow rate=0.5 x1000 x 402 joule /sec…

Q: Q.2. Discuss in detail different types of ball-milling and their advantages.

A: Ball mills are commonly used for crushing and grinding the materials into an extremely fine form.…

Q: Why do you suppose that girders are so often arranged to form triangles in the construction of…

A: Degrees of freedom for linkage are 0 for triangle, 1 for rectangle and 2 for pentagon etc...

Q: shown in the figure. Mercury fills a reservoir and is subject to standard atmospheric pressure. You…

A: Consider two point, one on the surface of the mercury outside the tube and other inside the tube.…

Q: If T is 90N, what is the value of Tx of m2? n T m.g Ⓒ = 40.3° m₂g

A: Given: Tension T = 90 N Angle made with horizontal θ = 40.3°   To find:  The horizontal component of…

Q: In unidirectional composites, cylindrical fibers are considered to be packed in square or hexagonal…

A: Let r denotes the fiber radius and a0 denotes the edge length of the unit cell. The square array has…

Q: A lead apron is placed over the dental patient. Why?

A: Lead apron are type of protective clothing which acts as radiation shield. It is made up of a thin…

Q: Which of these has maximum torque? The angle between the applied force and moment arm is 30 degrees…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Expla in the term 'partial pressure' and why Da lton's law is a limiting law.

A: When multiple gases occupy and share a common volume in the container , the the total pressure in…

Q: Why are flaps used at the leading and trailing edges of the wings of large aircraft during takeoff…

A:

Q: The figure shows a 50 kg lead cylindrical piston which floats on 0.68 mol of compressed air at 30°C.…

A: Given, Mass of cylindrical piston = 50kg Initial temperature= 30°C = 303K Final temperature= 300°C=…

Q: The piping system shown in the figure (which does not show details of all the fittings) is used to…

A:

Q: A block with 20 kg mass put on the floor. The weight of the block is .. * 20 N 50 N O 100 N O 200 N…

A: Given The mass of the block is m=20 kg. The mass of the body will remain constant but the weight…

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.