5 .Design Earthen Channel using Lacey's Regime Theory having following Data: Q = 103 S = Discharge cumecs m/m Slope Channel side slope z= 0.000132 2 1v:zh Lacey' silt factor f = 0.97

Q: Homework Use the routh's criterion to test the stability of the system with the following…

A: The answer for the given question is as follows.

Q: Using image bellow determine absolute velocity for propagation of action potential in median (X) and…

A: X-30 m/s ; Y-6.42 m/s

Q: te Vickers Hardness for rial if pyramid diamond

A:

Q: 1. Using the Routh's stability criterion, determine the range of K for stability for C/S eq. s' +…

A: please see the next step for solution

Q: Question 3 Part a: For the section shown, determine the: . Maximum elastic Moment M Fully plastic…

A:

Q: c) Show the computed shear and over-turning moment on the following graphs. FR P5 F4 r3 F2 BASE…

A: Step 1: Define the Point of Interest (POI):Identify the specific location in the structure where you…

Q: b) A tapered beam as shown in Figure Q4(b) is to be analysed using a Finite Element Analysis…

A: SUMMARY: - hence, we discussed all the points.

Q: the maximum flow graph in Gwith source V1 and sink v-

A: Given :- In the above question, a graph G is mention in the above given question   Need to compute…

Q: -) Figure 1.1 Unregulated Power Supply Theory Using the above formula compute the ripple (the) for…

A: The ripple factor is described as. The ratio of the RMS cost of an alternating present day component…

Q: Which of the following word equations describes the material balance simplified for a "closed"…

A: Given, equations for material balance. To choose the correct answer for closed system with no…

Q: The initial heat distribution over a steel plate is given by the function: u(x, y) = 80 yex-0.3y

A: function [heat_fn] = heat_fn(x,y) % f(x, y ) = 80 * y^2 * e^(-x^2-0.3*y^2) heat_fn = 80 * y.^2 .*…

Q: An iron rod is graded based on the following criteria: Magnetite content must be greater…

A: Program Approach: Include necessary header files to get a standard I/O. Define a main function.…

Q: For each of the following transfer functions, write the corresponding differential equation. X(s) 1.…

A: 1. Given transfer function: X(s)F(s)=s+2s3+13s2+5s+1 Cross multiplying, (s3+13s2+5s+1)X(s) =…

Q: Draw the transistor-level circuit and size the transistors in each of the gates so that its rise and…

A: According to the information given:- We have to draw the transistor level circuit and size the…

Q: The specification limits on a particular quality characteristic calls for an upper limit of 380mm…

A: A sampling plan should be developed that will provide a representative sample of the lot size.   A…

Q: Question 5.0 The flux falling on a table is 400 lumens. A.lf the area of the table is rectangular…

A: Already given: Lumens = 400 area = 100cm X 200cmorarea = 1m X 2m = 2m2

Q: 3.20 Calculate / and the current /for V= 700 mV for a pn junction for which N, = 10/cm 200 um, n, =…

A: Solution:   Given, V = 700 mV NA = 1017 /cm3 ND = 1016 /cm3 A = 200 µm2 ni = 1.5 x 1010 / cm³, Lp =…

Q: 8-33 and 8-35 The figure illustrates the connection of a steel cylinder head to a grade 30 cast-iron…

A:

Q: Problem 24: Use mesh analysis, find the currents flow through each voltage source. R1 R3 R$ E 를 10 V…

A: Answer   Current through 10V source 3.312A (UPWARD). Current through 6V source is 0.7898A (UPWARD)

Q: If the BOD3 of a wastewater sample is 75 mg/l and reaction rate constant k (base e) is 0.345 per…

A: Let us see the answer:- The answer is 3.69 mg/L

Q: Q1. Given the hazard rate function () = 2 × 10-5, Determine R(t) and f(t) at t= 500 h.

A:

Q: Q. No.2 What is the total resistance between point A and ground in below figure for the following…

A: here have to determine total register for parallel.

Q: 7. The initial heat distribution over a steel plate is given by the function: u(x, y) = 80…

A:

Q: H.W-A CRT has an effective deflection length of 2 Cm and distance of 1 mm. The acceleration voltage…

A:

Q: D. Single Phase Circuit Consider the circuit in Figure 2 - 1 Rídr Lfdr ZL Figure 2 -1 Given that Ra…

A:

Q: 3. For the given the function has static-1 hazards. F(W,X,Y,Z)=Em(0,1,2,5,8,10,13) a) Construct the…

A:

Q: For the ideal diode, the voltage across the load R₁ is given by [vs if vs > 0 VL 10 if vs ≤ 0…

A: The solution is given below for the above given question:

Q: please help me out with by step solution thanks

A:

Q: according to chebsyhevs theorem 95% = +or - 2 standard deviation 97% = +or - 3 standard deviation…

A: 68% percent of data falls within one standard deviation, 95% percent with two standard deviation,…

Q: Solve the following max flow problem using Ford-Fulkerson method

A:

Q: Design a wide flange W column 8 m in height to support an axial dead load of 1000 kN and a live load…

A: use W350x175 steel section Explanation:Step 1: Try section based on ASTM structural shapes…

Q: In the given tank and pump model given in the figure 1, activate any two malfunctions and analyze…

A: A Computer Program is a set of instructions , that can be executed by a computer to perform a…

Q: believe this needs to be in 3-D

A: Consider a three-dimensional crystal with a rectangular shape, dimensions 10 um x 1 um, lattice…

Q: YOUR TASK You need to produce a menu driven software written in C which allow the user to: a. Choose…

A: system("cls") does not work on C. Hence working on code apart from that part.

Q: 8 Provide MATLAB code to solve, please.

A: The MATLAB code to solve the following boundary value problem for the given functions f(x) using the…

Q: A soft to very soft silty clay layer 3 m thick exists between a layer of permeable clayey silty sand…

A: The solution to the given question is:

Q: Q2: Using the Routh's criterion, determine the stability of the closed-loop system that has the…

A: Routh–Hurwitz stability criterion is a mathematical test in control systems.

Q: (a) Find (by hand and calculator) the least squares fit and RMSE error for the periodic models y =…

A: note : As per our company guidelines we are supposed to answer ?️only the first question. Kindly…