4Y See the framing diagram above. Assuming 30x 2X 3 . X = 7 ft • Y = 3 ft • The load on the girder on grid line 1 is 700 #/ft. (Instead of point loads from beams, we will consider the load from the floor will act directly as a linear load on the girders.) • There are 12 beams (spans 1-2 & 2-3), 6 girders (spans A-B & B-C), and 9 columns. What is the total load on the column at B/1?

4Y See the framing diagram above. Assuming 30x 2X 3 . X = 7 ft • Y = 3 ft • The load on the girder on grid line 1 is 700 #/ft. (Instead of point loads from beams, we will consider the load from the floor will act directly as a linear load on the girders.) • There are 12 beams (spans 1-2 & 2-3), 6 girders (spans A-B & B-C), and 9 columns. What is the total load on the column at B/1?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Girders AC and DF have a width of 350 mm and a total depth of 500 mm. Given: Total dead load - 4.9 kPa (including wt. of slab and beam) Concrete f'e = 20.7 MPa Longitudinal bars fy = 415 MPa Live Load = 4.8 kPa Shear bars fyv = 275 MPa Distance on center of girders: Concrete cover = 70 mm L= 6 m, S = 2.8 m, Column = 0.35x0.35 a. ) For beam BE, calculate the factored shear force (kN) at the critical section. Assume a simply supported span. b.) Determine the spacing (mm) of two legs of 10 mm ø shear bars at the critical section. c. ) In accordance with NSCP provisions, what should be the maximum spacing (mm) of stirrups at the critical section of the shear. A 2.80 m E 2.80 m 6.00 m Girders 350x500 mm Beams 250x400 mm
How many Zero force members are there in the truss shown? В D F E A K H[100 kN 60 kN LL 60 kN O 2 O 3 5 O 7
Please answer all the questions. Show complete solution. Don’t round up nor round off. Draw the needed diagram
6
Q 3 List down the assumptions made in deteriming the truss.
It is desired to remove the spike from the timber by applying force along its horizontal axis. An obstruction A prevents direct access, so that two forces, one 350 lb and the other P, are applied by cables as shown. Compute the magnitude of P necessary to ensure a resultant T directed along the spike. Also find T. r Answers: P = i i 10" A link o 5" 8" 350 lb lb lb W
The double web girder is constructed from two plywood sheets that are secured to wood members at its top and bottom. Each fastener can support 60lb in single shear. Determine the required spacing, s, of the fasteners needed to support the loading of 2800lb. Assume A is pinned and B is a roller.
Can I please get full workings out for this past paper question please. I just need help with part 2
Situation A building has a steel frame layout as shown in the Figure. It must have support the following floor loads and materials. All of steel connections are "simply supported / pin supported". All of girders use are made of W 600 x 551 Use the load combination for design strength 1.2D+ 1.6L, and D + L for allowable strength, also = 0.75, and 2 = 1.75. Determine the following 1 a. The design uniform distributed load for beam F1-F2 b. The design uniform distributed load for beam B2-C2 c. The allowable uniform distributed load for beam B3-C3 d. The design shear for beam B2-C2 e. Nominal shear strength for beam B2-C2 (from letter d question) 2 3 4 6 m Concrete Slab 4 m Unit Weight (Scone) = 23 kg/m Thickness (t) = 100 mm Floor Finish (finish) = 0.15 kPa Electromechanical (mechanical) = 0.10 kPa Ceiling (qceiling) = 0.10 kPa Office and BPO occupancy (Goffice) = 2.9 kPa 6m A 6 m B 5m C I 5m D 1 3 m F 1
Situation 1 Light-grade channel is used as a purlin of a truss whose top chord is sloped at 15degrees from the horizontal. Properties of channel section: Sx = 6.19 x 10^4 mm^3 Sy = 1.38 x 10^4 mm^3 Simple Span = 6 m with one sagrod at L/2 Loads Roof Loads (applied at centroid of purlins) Dead Load = 0.95 kPa (including weight of purlin) Live Load = 1.2 kPa Allowable Stress: Fbx = Fby =110 MPa a. Determine the maximum spacing of purlins (m) due to dead load plus live load only. (Hint: Analyze in terms of s and DCR<= 1.0)
If beam BEH is hinged at the columns B, E, and H, determine its degree of indeterminacy.
Q9