480250DB360130320360450Dimensions in mmProblem 4A rectangular plate is supported by three cablesthat the tension in the cable AD is 444 N, determine the components ofthe force exerted on the plate at B, C, and D.asshown. Knowing

Answered: 480 250 D B. 360 130 320 360 450…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two cables are tied together at C and are loaded as shown. Knowing that P 327 N and R- 309 N, Determine the tension in cables AC. B 30 30
Show that, when a frame supports a pulley at A, an equivalent loading of the frame and of each of its component parts can be obtained by removing the pulley and applying at A two forces equal and parallel to the forces that the cable exerted on the pulley. (b) Show that, if one end of the cable is attached to the frame at a point B, a force of magnitude equal to the tension in the cable should be applied at B. A B A в т A A T T T T T т (a) (b) Flg. P6.90
Determine the reactions in pounds the hinge and the rocker exert on the beam supporting the distributed load. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations or answers) Magnitude and direction Magnitude in lbs. Ax- Magnitude is 0 Ay- By-
A 200-Ib block is suspended from an inextensible cable which is wrapped around a drum of 1.3-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of Inertia IG=10 Ib-ft-s^2 At the instant shown, the velocity of the block is 5 ft/s directed downward. Knowing that the bearing at A is poorly lubricated and that the bearing friction is equivalent to a couple M of magnitude 60 Ib-ft, determine the work or U1->2 (in ft-Ib) after it has moved 4.2 ft downward
-/5 : Two rods and one cable are attached to the supports at O. If two of the forces are as shown, determine the magnitude F and direction of the third force so that the resultant of the three forces is vertically downward with a magnitude of 1400 lb. F 830 lb 300 lb 8 10:38 pm 44 ENG 29°C Mostly cloudy 04/06/2022 0 48° ance is ± 1 in the 3rd nt digit. F = i, Type here to search -1080- Esc 0 35° 44 $ lb O O At % 5 F6 € 6 O & 7 7 8 8 ( ||| E
*6-76. Determine the horizontal and vertical components of force which the pins at A and B exert on the frame. 2 m 400 N/m D 1.5 m E 3 m 3 m F 1.5 m |A В
Your answer is partially correct. Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force, determine the distance d below point A to its line of action. 240 N 315 N Answers: M= R= i -345 i -120.60 Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise. Single resultant force. 210 N d = 349.65 670 mm 670 mm 670 mm mm N N.m
The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. Knowing that the entire shaft is made of steel for which G = 77 Gpa, determine the angle of twist at end A. 44mm -0.6m 60mm C 2000Nm B 30mm 0.2m 0.4m 250Nm A
10. The force system on frame GHIJK as shown, replace the system by a force equal to the resultant of the three forces, acting vertically at H and a force-couple acting horizontally at J and K. * |250N 1 m G' K 3 m 2m J 3 m 300N 600N A. R = 550N Į+; C = 1550N-m clockwise; Force-Couple: F = 775N+ at J & F = 775N→ %3D at K B. R = 650N Į+; C = 2350N-m clockwise; Force-Couple: F = 1175N- at J & F = 1175N at K C.R = 1150N Į+; C = 1250N-m clockwise; Force-Couple: F = 625N- at J and F = 625N at K D. None of the above
Question 3 of 10 View Policies Current Attempt in Progress Answers: MB = MA= The 43-N force P is applied perpendicular to the portion BC of the bent bar. Determine the moment of P about point B and about point A. Moments are positive if counterclockwise, negative if clockwise. i i P = 43 N < 1.3 m B 41° 1.3 m N.m N.m ■ -12 C E
Two cables are tied together at C and are loaded as shown. Knowing that P = 316 N and R = 357 N, Determine the tension in cables AC. %3D В 30° 30° R C /45°

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

480 250 D B. 360 130 320 360 450 Dimensions in mm Problem 4 A rectangular plate is supported by three cables that the tension in the cable AD is 444 N, determine the components of the force exerted on the plate at B, C, and D. as shown. Knowing