47 k2 100 k2 20 k2 (a) 560 k2 560 2 (b)

Q: Q OUT CLK

A: STATE TABLE OF D-FLIP FLOP: D(Input) Qn+1(Next sate) 0 0 1 1   CHARACTERISTICS TABLE OF…

Q: Q-1-a) From the circuit in the Figure-1, determine the DC-bias operation Parameters: (i) IB (ii) Ic…

A: Given:

Q: 21. If the specified linear measuring function is Vout = 1.4g – 4.35 V, the input voltage values of…

A:

Q: A- Explain the use of opamps as amplifiers by drawing a figure. B- Write the types of opamps.

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Determine the change in drain-source voltage to achieve the resulting amplification factor for FET…

A: We have an FET with,  Drain resistance (rd) = 2000 Ω transcoductance (gm) = 50 * 10-4 mhos…

Q: 4. In Figure 4, the input signal results in a base current of 10 mA peak and choose any value of Rc…

A:

Q: Submit a brief report on 3 different Analog and Digital applications of op-amp and represent a…

A: Analog applications of op amps: Op amp as a summing amplifier: The input voltages are applied to…

Q: Connect a thermistor (Resistance=500 – 1% per °C ) in a bridge (power supply =8V) with an…

A: Given:- Rt=500ohmα=1% per°cV=8voutput of inverting amplifier=4v at 30°t= final temperature=30°

Q: 1. A certain phototransistor has a BDC. 150. If I = 250, what is the collector current? 2. In the…

A: Please note that these 2 are different questions.  As per our guidelines we are supposed to answer…

Q: Q1 Analyse the circuit shown in Figure Q1, (а) Name the function of each Op-Amp, A1, A2, A3, and A4…

A:

Q: what is the construction and working principle of electronics amplifiers

A:

Q: An analog-to-digital converter outputs an analog voltage. True or false?

A: Given Analog to digital converter(ADC)

Q: 3:- Detine 4 only; Error, Passband, Standard, Negative Temperature Coefficient, Dynamic Range 24:-…

A:

Q: 1) Briefly describe and compare the different types of Analog to Digital Converters.

A: ADC (Analog to digital convertor)- It is used to convert analog signal to digital signal in data…

Q: Calculate the DC voltages and currents in the circuit. Find for the current emitter, collector…

A:

Q: 4. When amplifying the voltage signal, it is usually expected that the input resistance and output…

A: Amplifier An amplifier is used to increase/amplify the magnitude of voltage/current. A voltage…

Q: Output voltage from the circuit in Figure 1, 2, 3, 4 and 5 please :)

A: Step 1:Step 2:

Q: (a) Figure Q4(a) shows a circuit for voltage regulator. (VREF is a reference DC voltage). Vcc=3.3V…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Q2. The stabilizer current of the thyristor in the circuit is below 100mA and the delay time of the…

A:

Q: Q1 Analvse the circuit shown in Figure Q1, (a) Name the function of each Op-Amp, Al, A2, A3, and A4…

A: The response of individual stages of operational amplifier can be calculated based on the function…

Q: A. Draw the circuit diagram for a class B- Push Pull amplifies and descibe how to increase the…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: b) Considering the average input voltage found in (a), what will be the minimum value of R₂?

A: Given data, The maximum Zener current (Izmax)=100mA The maximum Zener Power dissipation (Pz)=1W The…

Q: In common source configuration the input resistance of a JFET will be approximately____. a.500 Ohm…

A:

Q: With neat diagram explain the construcation and working principle of Electronics Amplifiers

A:

Q: 2. Find the gain and also Vo for the given circuits. Name the circuit. (a) 33.3k2 25mV oM OVo 2.…

A:

Q: A DC source has an open circuit voltage of 50 V and an internal resistance of 2.5 N. The value A10…

A:

Q: 1. For the following circuit assume r = 30.6 1 Vee 16V a. Draw the small signal equivalent circuit.…

A: Given question is related to bjt in common emitter configuration it can be used as power amplifier

Q: Q-1-a) From the circuit in the Figure-1, determine the DC-bias operation Parameters: (i) IB (ii) Ic…

A: As per our policy, i have attempted 3 parts . Given  β=100RB=380 KΩRC=1 KΩVBB=VCC=12 V Calculating…

Q: Ts switching frequency of the buck type dc dc converter with an input voltage of 100 v is determined…

A: In this question we need to find which statements is wrong.

Q: Example 1: For the circuit shown in Figure 4 () Draw the DC load line (ii) Calculate the Q point if…

A: Given data: VCC=10 V R1=2500 Ω α=0.975 IB=50 μA (i) Load line can be drawn by using the below…

Q: Instructions Calculate the DC voltages and currents in the circuit. Find for the current emitter,…

A:

Q: Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load…

A:

Q: (iv) VBE (v) VB (vi) Vc (vii) VCE (viii) Ve

A:

Q: (b) A thermistor with the characteristics shown in Figure Q2 (b-1), is connected to Wheatstone…

A: The given circuit is shown below. The values of resistances of differential amplifier is R1=4 kΩ.…

Q: Q10. Determine maximum and minimum value of Zener current if value of series resistance is 1 K, load…

A: We need to find out maximum and minimum current flowing through zener diode . We will use normal kcl…

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.