120Part 1 Semiconductor Devices and Basic Applications+10 V2.47 Consider the circuit shown in Figure P2.47. Assume each diode cut-in volt-age is Vy 0.6 V. (a) Determine R1, R2, and R3 such that Ipi = 0.2 mA,In2 = 0.3 mA, and Ip3 0.5 mA. (b) Find V, V2, and each diode currentfor R1 10 k2, R2 4 k2, and Ry 2.2 k2. (c) Repeat part (b) forR 3 k2, R2 6 k2, and R3 2.5 k2. (d) Repeat part (b) forR 6 k2, R2 3 k2, and R3 = 6 k2.The diede cut in t+5 Vin FigeR2is 0.7VDetermine the vanenmE het nZDzpartoftमामाफतीFigure P2.47+5 V+5 VIpi. D,

Answered: Image /qna-images/answer/d01d7ebc-1755-4d92-a2df-80e2e211f25d.jpg

47 Consider the circuit shown in Figure P2.47. Assume each diode cut-in volt- age is Vy 0.6 V. (a) Determine R1, R2, and R3 such that Ipi 0.2 mA, Ip2 = 0.3 mA, and Ip3 0.5 mA. (b) Find V, V2, and each diode current for R 10 kS2, R2 4 k2, and Ry 2.2 kS. (c) Repeat part (b) for R = 3 k. R, = 6 kO, and R = 2,5 k2. (d) Repeat part (b) for %3D %3D %3D %3D %3D

47 Consider the circuit shown in Figure P2.47. Assume each diode cut-in volt- age is Vy 0.6 V. (a) Determine R1, R2, and R3 such that Ipi 0.2 mA, Ip2 = 0.3 mA, and Ip3 0.5 mA. (b) Find V, V2, and each diode current for R 10 kS2, R2 4 k2, and Ry 2.2 kS. (c) Repeat part (b) for R = 3 k. R, = 6 kO, and R = 2,5 k2. (d) Repeat part (b) for %3D %3D %3D %3D %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q²: A diode room temperature (VT=25mV) Conducts 1.0mA when it's forwar voltage is 0.7v. what will be the current in milliamps if the forward voltage is 0.5V?
Q2: For the circuit shown in Figure 1: 1. Describe the behaviour of a p-n junction in terms of semiconductor behaviour. 2. Describe and evaluate the circuit. Assume the values for the parameters in the circuit. You should critically evaluate the performance of the circuit and suggest potential applications. Figure 1: Electronic Circuit for Q2.
shown below is a diode circuit. If the input signal Vs= 36Vp-p and the DC voltage Vdc = 4V, what is the output voltage (in volts) of the circuit during the positive alteration?
3.56 Consider a half-wave rectifier circuit with a triangular-wave input of 5-V peak-to-peak amplitude and zero average, and with R= 1 k. Assume that the diode can be represented by the constant-voltage-drop model with V₂ = 0.65 V and r = 20 S2. Find the average value of vo.
(c) Figure Q4(c) illustrates a full-wave bridge rectifier used in ac voltmeter circuit. i) Explain the operation of diode D1, D2, D3 and D4. ii) Calculate the value of resistance R., ac sensitivity and de sensitivity. D1 D2 V=20Vme Rs 03 In=1mA R=2502 D4 R=2502 Figure Q4(c) Full Wave Bridge Rectifier
S2) Calculate the value range that the load resistance (Ry) must take in order for the zener diode to remain in continuous conduction in the circuit in the figure?
I need the answer only those parts. vi,vii,viii,ix,x, Please provide correct solution. And provide **ALL** those parts what i mentioned ( vi,vii,viii,ix,x) WILL UPVOTE YOUR ANSWER IF YOU PROVIDE CORRECT SOLUTION OF VI,VII,VIII,IX,X
(2-7) A full-wave bridge rectifier with a 120 Vrms sinusoidal input has a load resistance of 1kn. Determine:- 1) The de voltage available at the load. 2) Find the maximum current through each diode during conduction. 3) What is the required power rating of each diode.
This one.
Q2. a.find the diode curent where Is-30nA ,and the applied baise voltage-0.3v at temprature -22°C. b.for half wave rectifier ,draw circuit diagm and find Vde, Vrms & Vripp when Vin-30Vac. 03
Calculate the current (I) through the diode and voltage across the resistor (Vout). Assume V1 =15V,R1=6KN. Ge Vout V1 R1 Diode D1 is ON or OFF? Choose... Vout= Choose... Current (I) = Choose... v
For the full wave rectifier circuit shown, if vs=15sin(120nt) (V), R=10052, assuming constant voltage drop with VDo=0.7 J. 1. LDraw clearly and accurately with details the following waveforms: Source voltage (vs), load voltage (v.) 2. Describe in details the operation of the circuit indicating which diodes will be ON which ones will be OFF and state clearly the condition at which each diode will be ON or be OFF. 3. Calculate the mean load current (IRmean) given Vmean=2Vp/T. 4. Calculate the PIV. ac line Us voltage D2 Maximum size for new files: 10MB, maximum attachments: 2 Files 79 CE255/EE255 (01)-..