450 mm Water surface 600 mm -300- ILITY Cable Sea bottom

Q: A cylindrical tank is resting horizontally on the ground (the circular faces are vertical). The tank…

A: There are two types of forces that act on a circular surface: one type of force is radial force and…

Q: Use Image below Question: Gate AB is 2 m long and 1.8 m into the paper. Neglecting atmospheric…

A:

Q: wall as shown. a- Compute the magnitude of the resultant of horizontal forces on the sphere. b-…

A:

Q: The circular gate ABC in Fig.  has a 1-m radius and ishinged at B . Compute the force P just suffi…

A: Given: The radius of the gate, r = 1 m Depth of the point B from the free surface of water, h = 8 m…

Q: The corner of a floating body has a quarter cylinder AB having a length normal to the paper of 3 m…

A:

Q: Find height of water column corresponding to pressure of 70 KN/m2

A: Given data,  P=70KN/m² =70000 N/m² Let the density of water d=1000 kg/ m³

Q: The 600-lb, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making…

A: Լուծում;

Q: (b) Imagine holding two bricks under water. BrickA is just beneath the surface of the water, while…

A: Force needed to hold brick B is same as the force to hold brick A since buoyancy force acting on…

Q: 2. A 1124gpm of water is flowing in a round pipe such that the flow remains laminar. What is the…

A: #2 find the diameter of pipe.

Q: What would be the resultant force F of the triangular distributed load and its location d measured…

A: Triangular load is also termed as uniformly distributed load.  The magnitude of the triangular…

Q: Example: A cylinder 2.2 m in diameter and 3.3 m long supported as shown in Figure retains water on…

A: For solution refer below images.

Q: A plane is fitted with pontoons for operation on lakes. As it taxies out for take-off, the plane…

A:

Q: A solid cylinder of circular section of diameter d is of material with specific gravity S. This…

A: To find: The maximum length of the cylinder if the equilibrium is to be stable with the cylinder…

Q: A steel tank with inner diameter of 5m and a height of 5.20m contains Oil (specific gravity  = 0.80)…

A: SPECIFIC GRAVITY Specific gravity, likewise called relative thickness, proportion of the thickness…

Q: The tank in Fig. 1 is 3 m wide into the paper. Compute the hydrostatic (a) horizontal force…

A: width,w=3 mFor the horizontal force we consider the projected area of the curved surface.Depth of…

Q: A trough is full of liquid of weight density 9,000 N/m³. The ends of the trough are equilateral…

A: To set up: The integral for the force on one end of the trough. Given: The weight density of liquid…

Q: q6 A 1 kg cylinder of plastic has a length of 105 mm and a diameter of 40 mm. Calculate its specific…

A:

Q: A storage vat has vertical ends 3.6 m apart, of which one end is shown below. Oil (s=0.84) is stored…

A:

Q: Problem #4: Weightless gate AB is 5 ft wide into the paper and opens to let freshwater out when the…

A:

Q: A flotation buoy has mass 806 kg, volume 1.43 m, and is attached to the sea floor by a cable in such…

A: Given   Mass of buoy, m = 806 kg    Volume of buoy, V = 1.43 m3 Density of sea water = 1025 kg/m3…

Q: 3. Determine the vertical and horizontal forces on the cylinder shown in Fig. below. The cylinder is…

A:

Q: Q#1: What are the conditions of equilibrium for floating and submerged bodies

A: A submerged or floting body is stable if it comes back to it's original position after given a…

Q: A cylinder made of wood staves is filled with liquids of equal heights with specific gravity 3, 2…

A:

Q: Parameter Unit (a) FTOTAL (b) T1 (c) T2 (d) 01 (e) o2 Ib Ib Ib psi psi elele

A: Given: D= 6 ft H=12 ft h=9 ft sg=1.5 density=1500 kg/m^3=93.64 lb/ft^3 A=0.5 in^2 TO determine: The…

Q: Example: A hemisphere projection of diameter 0.6 m exists on one of the vertical sides of a tank. If…

A:

Q: A rectangular tank of dimensions: 2 m x 1.4 m x I m deep contains fresh water to a depth of 0.6 m. A…

A:

Q: A cube with edges measuring 80 mm is constructed of foam rubber and floats in water, with 50 mm of…

A: Given that, Side of cube, a = 80 mm h= 50mm Specific gravity,  sg= 1.36 We have to calculate…

Q: Calculate the Force on a piston when the Pressure applied P= 50 psi and the area of the piston is 20…

A:

Q: A sphere 1 m in diameter floats half submerged in a tank of oil (specific gravity = 0.82). What is…

A: Given:Diameter of sphere=D=1mSo,radius,R=12=0.5mSpecific gravity of oil=so=0.82Let minimum weight of…

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.