44. Design the fixed-bias network of Fig. 9.69 to have a gain of 8.

Q: What is the voltage drop across RC, VC, in volts?  (Enter the number, not the units.)

A: Given circuit is -

Q: Explain in clearly the difference between Intensive and Extensive readings.

A: Given Enumerate the differences between intensive and extensive reading. Please find the below…

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: hich of the following can’t be included in data required for coordination study? A)X/R ratio B)MVA…

A: characteristic curves of the fuses and breakers are generally analyzed in the coordination study

Q: Choose which answers are correct ‎‏What is the unit of slope of a Fuel cost curve ? a . $ / MWh b .…

A:

Q: What information is contained in the specification K, 10,000

A: Kp stands for the position error constant for the step input function.  here, Kp = 10000

Q: recall the topcis of the electronic Device and circuits

A: There are many topics in EDC  These topics are  1- Semiconductor diode  2-Diode circuit

Q: In static characteristics, is defined as the difference between the true value applied to a…

A: in static characteristics, Accuracy is defined as the difference between the true value applied to a…

Q: Q2. What are the major carriers in the depletion region? Explain.

A: Here i have described it.

Q: What is the acceptable minimum value of leakage current of HI-POT Test of electrical cables. Can you…

A: According to the question,what is the acceptable minimum value of leakage current of HI-POT Test of…

Q: What is HT supply?

A: What is HT supply?

Q: What is receptacle load ? Explain under 100 words...

A: The amount of load produced by a device inserted into a receptacle is referred to as a receptacle…

Q: Difference in the digital and the analog systems

A: Both digital and the analog systems are used to transmit and received information (or signals). The…

Q: Q2: (A)Find the following: 1- (110)10+ (0111)2.by using BCD numbers. 3-(3E91)16- (1F93)16by using…

A: The number system is used to represent information in digital electronics. Different bases exist in…

Q: tronic components definitions and si units and color coding

A: Electronic components : There are mainly two type of Electronic components one is active Electronic…

Q: Label the parts of Tubular Steel Poles

A: Steel tabular poles are not commonly used poles these poles are used when there is need of low cost…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: Please show the work in between the rearranged formula and the answer

A: Given: Calculate the S/N in dB if the passband circuit is 48kHz to 64kHz and the maximum bit rate is…

Q: Q1. Convert following numbers in given radix system: a. (173)10 into hexadecimal b. (2E3)16 into…

A:

Q: The mutual inductance between two coupled coil is 25 mH. If the turns in one coils are doubled and…

A: Given: Mutual inductance of two coupled coil is M=25 mH Turn of one coil is doubled and that in the…

Q: 19. Identify the response time of a meter. a. Time taken by output to reach final constant value…

A: Identify the response time of a meter. It's depend on the parameter.

Q: 3. Explain the successive approximation type ADC with neat schematic diagram.

A: Successive approximation ADC: The successive approximation ADC is a type of converter that converts…

Q: 3) What is the dropout ratio? What is the advantages of dropout ratio in power systems. (min 1 page)

A: A pick-up and drop-out ratio terms related to protective relays. The pickup current of a circuit…

Q: What is national electricity grid

A: In this case, we need to explain what is national electricity grid.

Q: The circuit shown in Figure Q5.1 consists of a current source connected to a load via a cable. The…

A: Given circuit is - Value of current source is -

Q: Explain the Difference between the Fundamental and Derived Unit.

A: There are generally  three types of units which are used to typically measure a particular physical…

Q: What do you understand by Safety factor, puncture and Flashover of Insulator

A: The part section of a pin type insulator is shown in  the figure below:

Q: At pinch-off voltage, the drain current in a FET is ___. Choose the correct answer: a.zero…

A: At pinch-off voltage, the drain current in a FET is ___.   Choose the correct answer: a.zero…

Q: Hi for case 3 is explain on which question ? either (a) positive or negative or for question (b) pls…

A:

Q: Explain with a neat block diagram the measurement of temperature using RTD

A: On the principle of metal resistance increasing with temperature we use a device which is Resistance…

Q: What is the UPS

A: A uninterruptible force supply (UPS) is a gadget that permits a PC to continue to run for in any…

Q: Give the concise definition or process of getting the equations in each loop/mess (Mesh Analysis) in…

A: Let us try to understand the concept of mesh analysis in this answer.

Q: 10. Describe with one sentence what the shape functions in FEM are.

A:

Q: Question 4 What do you do to an asynchronous counter to let it count from 1 to 13? (Handwriting…

A: The solution is given below

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.