420°V -j1Q Find Io using superposition. 2Ω 2290°A 1245° A -j2N j5Ω Find Io in the same circuit as in problem 7.1 using mesh analysis.

Q: Q6: For the following circuit, find the total resistance between points A,B (Req) and the total…

A: As we can see that  F and G are at same point and D and C are at same point so we will redraw the…

Q: Explain the environmental hazard of Nuclear power generation with neat diagram

A: Nuclear power plants use uranium as fuel. During the process of mining uranium released high amounts…

Q: explain what happened as the lamp load increasing through shunt generator

A: The ammeter displays the load current readings, while the voltmeter displays the end voltage value.…

Q: With neat sketch explain the types and operation of oil circuit breaker

A: Types of the circuit breaker, 1. Low oil circuit breaker 2. Bulk oil circuit breaker Plain break…

Q: In a natural circulation solar water heater, collector has a glass cover on the top and an material…

A: Solar water heater uses solar thermal collector to heat the water by sunlight.

Q: QUESTION 7 Match Collumn A and Collumn 8? Properties of Metal v Britleness A. the property of a…

A:

Q: g Technology- Toronto CHAPTER 7: SOLDERING TECHNIOUES ES 7.5 QUESTIONS Which tools will you need for…

A: Note: According to bartleby guidelines, we have to answer only first question. 1) Soldering is the…

Q: brownout is defined as: a slightly decreased voltage lasting from seconds to minutes or more

A: In this question we will define brownout in power system....

Q: Explain the working of the Potential meter float gauge with a neat diagram

A: Draw the Potential meter float gauge: Based on the displacement of the float, the float gauge…

Q: 1.a. If an environment may contain moisture, you should use lamps with bases that are made of A.…

A: 1 a . Moisture in environment means metal can be corrosive . So we have to select the base which…

Q: Which among the following is NOT a power system load? Select one: O a. Circuit Breaker O b. Motor O…

A: Power system load is a physical unit /device that consumes power. Refrigerator fan and motor…

Q: What is voltage reference?

A: A voltage reference is an electronic device designed to maintain an accurate, low noise. It ideally…

Q: Give a sample of corroded materials at home and suggest if weather or not corrosion prevention is…

A: Corrosion :   Corrosion is the process in which the metal form it's oxide and hydroxide which more…

Q: What is a circuit breaker? What is the most important parameter that helps to determine the rating…

A: A circuit breaker is a device that can detect overloads above its rating in a circuit and…

Q: How do you define an IC, for short?

A: Integrated Circuit: An integrated circuit is a small semiconductor-based electronic device which…

Q: Explain bus bar and bus bar chamber

A: In this question we will write about bus bar and bus bar chamber....

Q: Write the report on “Increase of fluorescent lamp and power factor”

A: Fluorescent lamps: Fluorescent lamps, often known as fluorescent tubes, are low-pressure…

Q: Determine how many degrees of lead in each question?

A:

Q: 3 phase fully controlled rectifier has a 3 phase line to line supply voltage of 410 V rms at 50 Hz…

A: A full-wave rectifier is AC to DC converter. A three-phase fully controlled rectifier converts AC…

Q: (i) The full-load current, (ii) The full-load copper losses, (iii)The full-load efficiency, (iv)The…

A: The DC shunt generator has,  Terminal voltage Vt=450 V Armeture resistance Ra=0.75 ohm Shunt field…

Q: Discuss five (5) good practices in electrical circuiting.

A: Always use gloves while working with electrical equipment and gloves must be insulated. While…

Q: What will be the unit of hole mobility

A: The solution is provided in the following section:

Q: 4. What are types of SPIM.

A: SPIM stands for Single Phase Induction Motor. These are simple motors which operates on single phase…

Q: -Discuss 5 differences between standard microprocessors and microcontrollers -Describe the RISC…

A: There is a total of three questions related to microcontrollers and microprocessors. The first…

Q: 4. What is PPE?

A: here we have to find the what is PPE.

Q: What is skin depth in power system?

A: Skin Effect : In AC systems There is a non uniform distribution of current in a conductor.The most…

Q: Alternating current is __________. Select one: A. AN ALTERNATING FLOW OF ELECTRONS B. ELECTRONS…

A:

Q: f. If the lower sphere is replaced with a sharp needle, is the breakdown voltage going to be higher…

A: Here it is asking that if the lower sphere is replaced with a sharp needle then what will happen to…

Q: Briefly discuss the 10 electrical hazards in the laboratory and give the corresponding preventive…

A: Working in an electrical laboratory is a task that need our care towards the safety. Electrical…

Q: , explain the FET types , working principles, structure and applications.

A: There are three terminals present in FET such as drain, source, and gate. FET stands for the…

Q: What role does environmental testing play in assessing the reliability of electronic components

A:

Q: A semiconductor is a material that has _____ energy band gap. a)no b)wide c)narrow d)nuclear

A: Energy band gap is the difference in the energy between the conduction band and the valance band. A…

Q: How do the different parameters vary with ic?

A:

Q: Q2: Define the component of Furnace temperature control system as a block diagram and the function…

A: The block diagram of the furnace temperature control system is shown below:  The components in the…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.