410 MPa 25 kpsi For th princ the 55 MPa 13 kpsi 300 30 kpsi MPa (a) (b)

Q: Required information The state of stress at a point is ox= 19 kpsi, oy= 0 kpsi, oz= 19 kpsi, Txy= 38…

A:

Q: problem: In the tollowing Figures, Find the force torque at the given paints. 200 N Loo N 200 N EMA…

A:

Q: Q1 show thot the force F-ljz-6xZ)+(2xyz) J+ (3xyz-6²z)is cors ervative, hence find i the Patenial…

A: Given: F=(y2z3-6xz2)i+(2xyz3)j+(3xy2z2-6x2z)k

Q: 40 MPa 35 MPa -60 MPa Figure 1 Due to the applied loading, the element at one point on the solid…

A:

Q: Find the insitu stress

A: We will use the formula to find the resultant of two stresses on any oblique plane

Q: What is the true stress?

A: Need to find True stress.

Q: as shown below; b) Compute the amplitude of the steady-state vibration and the phase angle if W = 6…

A:

Q: Part A Suppose that o, = 170 kPa and o, = 610 kPa. Determine the equivalent state of stress on an…

A:

Q: a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for…

A:

Q: Q2 A) For a flow rate of 300 liters/second at a velocity of 1.3 meters/second, design a seamless…

A:

Q: Uniform and non uniform stress, gives proper solution explanation with diagrams.

A: Given data Uniform and non uniform stress, gives proper solution explanation with diagrams.

Q: 0-5G & 0. 1P 4ield strey. is bound 84pmpa ę Aoisson's rat The Piincpal Strey 68 mochine Component…

A:

Q: ? If you know FED, how will you determine FEF 1000 N 3000 N 1000 N b YE b 1000 N a F A 30 a 2 m- 2 m…

A: Option b is correct.

Q: What will be the occerelalion at point L if theuniform KL bor is left horigontal. 2m Support…

A: Given, The mass of the bar, m=25 kg The length of the bar, L=4 m

Q: for q1) B at the point : frictional force at A is...the frictional force in the vertical direction…

A: Yes, you are right. The friction force in the vertical direction at point A has not been included in…

Q: An engine cylinder is 127mm in diameter, and the piston stroke is 508mm long, the clearance volume…

A:

Q: S-1) Given in Figure 1; a) Find the dimensions d, b and c? b) Calculate the stresses occurring in…

A: Stress : When an object is applied an external force or moment a resistance force is setup within…

Q: Draw shear force diagram along with calculation and write the accurate values in the diagram..

A: Shear force diagram represents shear force at every section of the beam. Shear force at any…

Q: xample. Drau the shear force and inding mimemts 2.0kN 1.6KN 1.5kN HA 1m 1m 1.2m 0.8m

A:

Q: A 200 MPa 100 MPa 150 MPa

A: Given Data

Q: The specification of a cylindrical vessel are as follows: D = 350 mm t = 12 mm P = 4.5 MPa Determine…

A:

Q: Data: P = 2 kip d = 3.6 inch w = 305 millimeters t = 0.03 meter r = 5.08 centimeter h = 0.6667 feet…

A:

Q: of pressure include?

A: Given :- Standard of pressure .

Q: How can the theory be applied to find the maximum allowable shear stress for thick walled cylinders?

A: Answer: Maximum allowable shear stress for thick walled cylinders: As, we know that from maximum…

Q: gue and Fatigue loads 2) Four categories of fatigue design situation steel tube carries liquid at 7…

A: (1) Fatigue load and Fatigue load material weariness is a peculiarity where construction bomb when…

Q: Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure…

A:

Q: Im 35 N/m 2m 30 N Im в 85 N 100 N.m 60 2m 2m 0.5m 1.5 m

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: 151 wLx 113 wL²x wx4 24L ,2 0 = wx3 - - 340 510

A: Given: The equation is given below: -Wx424L-Wx36+151WLx2340-113WL2x510=0

Q: In a) why you wrote ( m + 5m) , where that 5m came? You have m1 = m and m3 = 4m in the problem. So…

A: Given: The mass of the block: →m1=m And mass of the disc: →m3=4m this mass is the complete mass of…

Q: A state of stress at a point A is given by ox 210 MPa, oy = -140 MPa, and txy = 95 MPa. What is the…

A: Given, σx=210 MPaσy=-140 MPaτxy=95 MPa

Q: Find the work done Force=0.433 N Displacement=0.22 m

A: Given data : Force=F Displacement=d   Required : Work done

Q: A single cylinder engine operating at 1,500 rpm develops a torque of 10 N- m. The Friction power of…

A: Given:N=1500 rpmT=10 N.mFP=0.5 kW

Q: T1= 50c , T2= 54c , P1=2.5 bar , P2= 143 bar Find n??

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.