40 MPa 10 MPа 60 L. 60 10 MPа 40 MPа

Q: A 463-N object is hung from the end of a wire of cross-sectional area 0.03 cm-. The wire stretches…

A:

Q: 5. (a) Explain the differences in edge and screw dislocations. (b) Locate your screw dislocation at…

A: A) Edge and screw dislocations are two types of crystal lattice defects that can occur in materials.…

Q: he deflection of point B in

A:

Q: Which type of stress occurs when an external force tends to twist or distort an object along a plane…

A: Note:- When a body is subjected to external force than deformations occur in it, to restore it into…

Q: QUESTION 16 The T-beam is made of a nylon. The allowable stress is 24 MPa in tension and 30 MPa in…

A: The area of the top section will be, A1=80×30 ⇒A1=2400 mm2 And the area of the bottom section will…

Q: The graph below shows the experimental stress - strain graphs for two materials, A and B. Identify…

A:

Q: What can be said about the curves in the stress-strain graph given below Strain A Polymer A isa soft…

A:

Q: 10 lb 7 lb w=3lb/ft What is the value of the shear at point a? What is the value of the shear at…

A:

Q: The coefficients of static and kinetic friction between the 50-kg crate and the ground shown in…

A:

Q: Why R_[Ay) is calculated here? Explanation required

A: Step 1:Given data:A=6 mm2P=1.8 KNStep 2:Here A and B are left, right nail and RA,RB are reaction…

Q: The stress-strain graphs for materials A and B are shown below. The graphs are drawn to the same…

A: Hook's Law :  When an external force  applied to the material, It deforms. This means that the…

Q: A one metre long circular concrete beam, diameter 400mm, supports a 10kN load in the middle and is…

A: We know that the tensile stress is given by,Now, the given concrete beam is a cylindrical structure…

Q: Determine the strain-stress relations of an isotropic material for a cylindrical coordinate system.

A:

Q: When a rope is pulled on either side, what is the stress acting on it? a) Compressive stress b)…

A: B

Q: The 60-mm-diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tallow=85…

A: Given that, The diameter of the shaft, d = 60 mmThe allowable shear stress on the shaft,…

Q: What will be the shear stress value?

A: Apply Hooke law of elasticity

Q: Problems - Stress, Strain, and Young's Modulus P10-5. Zartan's vine, initially 6 m long, has a…

A: Given, Initially length of the vine, L=6m The Young's modulus, Y=0.1GN/m2Y=0.1×109N/m2 Stress,…

Q: The graph below shows the tensile stress against strain for a glass fibre. stress/10°Pa 100 80 60 40…

A: (a) given graph is between tensile stress vs strain in glass fiber it's a straight line and slope of…

Q: o is when a force causes compression and the object shrinks * O Inertia compressive stress, O…

A: Answer:-  tensile stress  Sigma is when a force causes compression and the object shrinks - tensile…

Q: If the deformation produced in 20 mm length rod is 0.085 mm, the strain is equal to: Select one: a.…

A: (d) 0.00425

Q: What is the strain? a) Ratio of elongation of a material to the original length b) It is force per…

A: Option B is correct.

Q: The 3 nails in the figure can withstand an average shear stress of 40 MPa. Determine the shear…

A: Write the given values with the suitable variables. τ=40 MPa=40×106 Par=4 mm=4×10-3 m Here, τ and r…

Q: The stress-strain graphs for two materials A and B are shown in the figure. The graphs are drawn to…

A: Stiffness: It is the ratio of the applied force to the deformation in the object within elastic…

Q: In the linear region of the Strain vs. Stress diagram is called Elastic Modulus * True False

A:

Q: A steel rod 3 in. in diameter is subjected to a tension force of 5500 lb. The rod is 10 ft in…

A:

Q: What is the slope of the tangent drawn to the net force curve at equilibrium distance? Lütfen birini…

A: Required : What is the slope of the tangent drawn to the net force curve at equilibrium distance.…

Q: Subject: Physics Identify what is being asked. 6. It is the ratio of tensile or compressive stress…

A: Solution:-Given that6. It is the ratio of tensile or compressive stress to the longitudinal strain…