4.F3 Bar AC supports two 400-N loads as shown. Rollers at A and C rest against frictionless surfaces and a cable BD is attached at B. Draw the free-body diagram needed to determine the tension in cable BD and the reactions at A and C. 100 mm 100 mm -300 mm 400 N 400 N 250 mm D A 150 mm -500 mm Fig. P4.F3

4.F3 Bar AC supports two 400-N loads as shown. Rollers at A and C rest against frictionless surfaces and a cable BD is attached at B. Draw the free-body diagram needed to determine the tension in cable BD and the reactions at A and C. 100 mm 100 mm -300 mm 400 N 400 N 250 mm D A 150 mm -500 mm Fig. P4.F3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4.) The uniform 4-kg rod AB is supported by a ball-and-socket joint at A and by the cord CG that is attached to the midpoint G of the rod as shown in the figure. The rod leans against a frictionless vertical wall at B. Determine the reactions at A and B and the tension in cord CG. [Answer: T = 20.8 N, Ax= -14.7 N (down), Ay= 29.4 N, Az 11.0 N, B= 29.0 N, where the positive answer indicate the reaction goes in the positive direction of the respective axis and vice versa] Hints: Note the given mass from which you need to calculate weight. IF G is is the midpoint of the rod, then the x, y, z coordinates of that point can be taken to be half the x,y,z components of the position vector FAB 150 mm, B 400 mm 0 150 mm 600 m G
Please help me
i need the answer quickly
4. Determine reactions at A and D of the frame shown. y 4 kN/m 4 kN/m в 1.5 m 2 m 10 kN-m 20 kN 3 m 4m-
Question 2: 600 N A EO 1 2.5 m B- I 2.5 m D+ 2.5 m 2.5 m A 600-lb horizontal force is applied to pin A of the frame shown. Determine the support reactions and the forces acting in the joints on the two vertical members of the frame.
Problem 4.30 4.30 The horizontal force P is applied to the handle of the puller. Determine the resulting tension T and all the other reactions as necessary. P = 120 lb Coplanar system, one rigid body, two supports, one 24 in. external load. B В 40° 20° A -6 in.-
y 150 mm 100 mm TB 200 mm D Tc T'c PROBLEM 4.91 Two transmission belts pass over a double- sheaved pulley that is attached to an axe supported by bearings at A and D. The radius of the inner sheave is 125 mm and the radius of the outer sheave is 250 mm. Knowing that when the system is at rest, the tension is 90 N in both portions of belt B and 150 N in both portions of belt C, determine the reactions at A and D. Assume that the bearing at D does not exert any axial thrust.
PROBLEM 1: Determine the tension in each cable and the components offorce reaction at D needed to support the load. Required: 1. Find dx, dy, and dz with complete solution
The bent bar as shown below is supported by a cable AE, a ball-and-socke joint at O, and a journal (slider) bearing at D. At the journal bearing D, the mome support reactions and the force support reaction along y-axis are zero. The 2-kip force and the 6 kip-ft couple-moment are parallel to z-axis and applied at point B Determine the tension in the cable AE and the support reactions at O and D. A 4 ft X MEST Z 6 kip-ft 2 ft B 2ft 2 kips 3 ft [ 1 kip = Lo = 1000 lb. 1 E 14 ft y
A thin ring of mass 2 kg and radius r=140 mm is held against a frictionless wall by a 125-mm string AB. Determine (a) the distance d, (b) the tension in the string, (c) the reaction at C.
Identify all the zero-force members in the trussesbelow.