4.8 An ideal chopper is operating at a frequency of 500 Hz from a 60 V battery input. It is supplying a load having 3 2 resistance and 9 mH inductance. Assuming the load is shunted by a perfect commutating diode and assuming battery is loss less, what is the mean load current at an on/off ratio of 1/1? (a) 10 A (b) 15 A (c) 20 A d.c.(1-K)

4.8 An ideal chopper is operating at a frequency of 500 Hz from a 60 V battery input. It is supplying a load having 3 2 resistance and 9 mH inductance. Assuming the load is shunted by a perfect commutating diode and assuming battery is loss less, what is the mean load current at an on/off ratio of 1/1? (a) 10 A (b) 15 A (c) 20 A d.c.(1-K)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Build the following circuit. Use the function generator to obtain the specified AC input voltage. D4 D1 + RL 1.2K + VsN D3 Y D2 9V sin(2n 50 t) Verify the amplı, 'de and frequency of the output waveform on the load resistor, RL. Peak voltage: Waveform period: Frequency 1.d) How much power would have. en dissipated on the diodes in total, if the same output waveform was obtainea sing a full-wave rectifier with a center- tapped transformer?
The single-phase half-wave circuit with a com mutating diode is used to supply a heavily inductive load of up to 15A from a 200 V a.c. supply. Determine the mean load voltage for firing delay angles of 180°, neglecting the thyristor and diode volt-drops. Specify the required rating of the thyristor and diode. * 15V 12V ov 10V
The three-phase circuit shown in figure 1 is 220 Vrms per phase and 50Hz. Diodes are real. The circuit produces an output shown in Figure 2. Indicate the conduction angle of diode D5. What times does this conduction correspond to? Use the first cycle only (0-360°). to-0 sec.
(c) Reverse recovery is a common problem in a diode. It can increase switching losses, increase forward voltage and induce voltage surge. (i) Explain how reverse recovery can increase switching losses in a diode. (ii) Figure Q1(c) shows that characteristic of reverse recovery in a diode. Based on the figure, calculate the peak reverse recovery current I, I (A) dls dt 30 A Q,, 1 us 3 us Figure Q1(c): The characteristic of reverse recovery in a diode
14.3 V Answer the following questions, since the minimum voltage value to transmit the zener diode in the figure given above is 9V and the power of this Zener diode is 0.3 watts. a) draw a parallel Clipper circuit that will give the output signal given in the figure. b) enter the name of the parallel Clipper circuit that will give this output voltage.
Answer a,b,c,d
PLEASE ANSWER THIS MCQ
Draw the characteristics of Ideal and practical diodes. A semiconductor has electron and hole mobilities as Hn = 7500 cm³ /V. sec, Hp = n = 3.6 x 1012 cm-3. Find (i) The hole concentration when conductivity is minimum. (ii) The minimum conductivity. 300 cm /V.sec and
Analyse the voltage waveforms of the input, Vị and the output, V, for a clamper circuit shown in Figure Q3(b)(i) and Figure Q3(b)(ii). V. V. 10 V 3 V -10 -17 (i) (ii) Figure Q3(b) If the ideal diode is replaced with a silicon diode, explain the changes of the output voltage measurement.