JU4.7 and 4.8 Two W4 × 13 rolled sections are welded together asshown. Knowing that for the steel alloy used, øy = 36 ksi and ơŋ58 ksi and using a factor of safety of 3.0, determine the largest couplethat can be applied when the assembly is bent about the z axis.14Fig. P4.7Fig. P4.8VC

Two W4×13 rolled section are welded together as shown in given figure. Yield stress of steel alloy,…

4.7 and 4.8 Two W4 X 13 rolled sections are welded together as shown. Knowing that for the steel alloy used, oy = 36 ksi and ou = 58 ksi and using a factor of safety of 3.0, determine the largest couple that can be applied when the assembly is bent about the z axis. HH Fig. P4.7 H •C Fig. P4.8

4.7 and 4.8 Two W4 X 13 rolled sections are welded together as shown. Knowing that for the steel alloy used, oy = 36 ksi and ou = 58 ksi and using a factor of safety of 3.0, determine the largest couple that can be applied when the assembly is bent about the z axis. HH Fig. P4.7 H •C Fig. P4.8

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 2 14600ksi, apr For the shown structure, AB is made by C83400-red-brass (Ebr 9.8 × 10-6/ °F) and BC is made by 2014-T6-aluminum (Eal 10600ksi, a al = 12.8 × 10-6/°F). AB and BC are joined at the collar B and fixed connected at their ends. The cross sectional area of each member is 1.75 in². If there is no load in the = member when T₁ 50 °F. Now the temperature for both members are increased to T₂ = 120 °F. Determine (1) Reaction forces at fixed end C (2) The average normal stress in the member AB (3) The average normal stress in the member BC (4) Eventually, how far will the collar B be displaced? = = 3 ft 2 ft
The aluminum rod AB (Gal = 27 GPa) is bonded to %3D the brass rod BD (Gpr = 39 GPa). The portion CD of %3D the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T. 60 mm 2T 36 mm T 250 mm 375 mm 400 mm
Show Stress/ strain curve for nitinol and steel (2 separate charts please)
H.W 3 Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in Figure 3. mensions of the composite cross section are b1 = 80 mm, d¡ = 240 mm, b2 = 10 mm, d2 = b2 The di- |di 120 mm, and a = 60 mm. Deter- (2) (2) %3D mine the maximum bending (1) a stresses produced in both the wooden beam and the aluminum b1 plates if a bending moment FIGURE 3 +6,000 N m is applied M2 %3D about the z axis. Assume that Ej = 12.5 GPa and E2 = 70 GPa.
If the modular ratio is equal to 7, and the Modulus of Elasticity of the Steel is 200,000 MPa. What is the value of fc'?
To get adequate strength and ductility for mild steel, up to What percentage of corbon content is required? а. 0.3 % b. 0.4 % О с. 1% O d. 0.6 %
REACTION OF A RIGID PLATE II A) Determine the internal and external reaction forces of a composite structure. To check the solution you will need to specify reaction components Ax, Az, Ma, Bx, Bz (body II), Cx, Cz (body III), Dx, Dz, Ex, Ez (body IV), Fx, Fz (body V), G (force transmitted by the member gj), H (force transmitted by the member hj), Kx, Kz. coefficient's are a= 1,1 b= 0,6 c=1.1
At a certain point in a structural member, the value of ox = -45 N/mm², ay = 75 N/mm² and t = 45 N/mm2. The principal stresses will be
A mild steel flat of width 120 mm and thickness 10 mm is bent into an arc of a circle of radius 10 m by applying a pure moment 'M'. If E is 200 GPa, then magnitude of the pure moment 'M' will be
Which of the following parameter represents principal stresses: T_a none of the available option O_X O_y 0_a
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 32-in.-long bronze [E = 13700 ksi] bar with a cross-sectional area of 1.29 in.2. Bar (2) is a 48-in.-long aluminum alloy [E = 10300 ksi] bar with a cross-sectional area of 2.19 in.2. Assume L1=32 in., L2=48 in., a=25 in., b=57 in., and c=15 in. Both bars are unstressed before the load P is applied. If a concentrated load of P = 26 kips is applied to the rigid bar at D, determine:(a) the normal stresses σ1, σ2 in bars (1) and (2).(b) the downward deflection vD of point D on the rigid bar.
H.W 3 Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in Figure 3. mensions of the composite cross section are bj = 80 mm, d1 = dz 240 mm, b2 = 10 mm, d2 = The di- di %3D %3D 120 mm, and a = 60 mm. Deter- (2) (2) (1) mine the maximum bending stresses produced in both the wooden beam and the aluminum b1 plates if a bending moment M = +6,000 N m is applied about the z axis. Assume that E = 12.5 GPa and E2 = 70 GPa. FIGURE 3 %3D