4.69 (muờa Water flows in the branching pipe shown in Fig. P4.69 with uniform velocity at each inlet and outlet. The fixed control vol- ume indicated coincides with the system at time 1 = 20 s. Make a sketch to indicate (a) the boundary of the system at time 1 = 20.1 s, (b) the fluid that left the control volume during that 0.1-s interval, and (c) the fluid that entered the control volume during that time interval.

4.69 (muờa Water flows in the branching pipe shown in Fig. P4.69 with uniform velocity at each inlet and outlet. The fixed control vol- ume indicated coincides with the system at time 1 = 20 s. Make a sketch to indicate (a) the boundary of the system at time 1 = 20.1 s, (b) the fluid that left the control volume during that 0.1-s interval, and (c) the fluid that entered the control volume during that time interval.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steady, incompressible and inviscid water flows inside the given system, if the force F is needed to hold the system stationary, what is the work W (W=F x L) joule is needed to move the system a distance L=15.5 m. V1=3 m/s 2 A1=0.1 m p1=200 kpa 1 2 m F 2 2 A2=0.2 m
Q6: Find the shear flow solution of incompressible fluid with flow : v1 = 0, v2 = 0 and V3 = v3(x) , no body force. 3.5 .........
Q3. In the two dimensional situation shown, the following quantities are given: u = 50, v, = 20, PN =0, PE =10.The flow is steady and the density is uniform. The momentum equations for u, and v, VN are given by: u=d. (PP-PE) v=d, (PP-PN) where the constants d and d, are given by d = 1, d, = 0.6. The control volume shown has Ax = Ay. Use SIMPLE algorithm to obtain the values of u, V and pp. W 3 Ax N n P S S e Ay E
Air flows through a compressor under steady flow conditions. At suction V1=0.75m3/kg, v1=30m/s At discharge: V2=0.25m3/kg, v2=40m/s.. Determine the diameter ratio of the discharge pipe to that of the suction pipe. (Ans. 1:2)
Steady, incompressible and inviscid water flows inside the given system, if the force F is needed to hold the system stationary, what is the work W (W=F x L) joule is needed to move the systema distance L=6.3 m. V1=3 m/s A1=0.1 m p1=200 kpa 2 m A2=0.2 m ENG 10:06 US 07/05/2 DELL FZ F8 F9 F10 F11 F12 PrtScr Insert Delete PgUp PgDn
A 200 mm diameter pipeline is laid on the ground. At a particular point, the piezometric head is 20 m. Total energy head of water at a point is 26 m. The Discharge (L/s) of water through the pipe is
4.5 The water flows in a 4m wide canal at a velocity of 5 m/s. A wedge-shaped column bifurcates the stream, as shown in Fig. 4.29. Calculate the force per unit depth exerted by the water stream on the column, if the wedge angle (a) is 30°. V=5m/s V=5 m/s V=5 m/s Fig. 4.29 [Ans: 3407.4N]
Water enters a 5-L tank at a rate of 4.00 kg/s and is withdrawn from the tank at a rate of 6.00 kg/s. The tank is initially four-fifths full. (a) Write a mass balance for this process by assigning a variable function to the mass of water at time t. Describe the terms that are present in the balance; give reasons for deletion of any terms. (b) Solve the balance to find how long it will take the tank to drain completely.
(b) A jet of water 500 mm in diameter with a velocity of 20 m/s strikes a flat plate inclined at an angle 0 to the axis of the jet as shown in Figure Q2 (b). Determine the angle 0 as the anchoring force, FĄ is 6000 N.
Lubricating oil is pumped to flow with velocity, V between two stationary paralle! plates separated by a thin gap of b = 1.8 mm as shown in Figure Q4. The gauge pressure at the inlet, Pn, is 100 kPa gauge. The pressure changes linearly to the atmospheric pressure at the outlet. Assuming the oil as an incompressible, steady and fully developed laminar flow of viscous fluid, detemine the equation of the velocity profile and the volume flow rate, Q. Calculate the Reynold number for the flow to justify that the flow is indeed laminar. [Lubricating oil properties: µ = 72.5 x 10° kg/m.s and p = 865 kg/m³] 1.0 m Pin y Pout 0.8 m V Figure Q4