4.62 (wILEYo Water flows through a duct of square cross section as shown in Fig. P4.62 with a constant, uniform velocity of V = 20 m/s. Consider fluid particles that lie along line A-B at time 1 = 0. Determine the position of these particles, denoted by line A'-B', when t = 0.20 s. Use the volume of fluid in the region be- tween lines A-B and A'-B' to determine the flowrate in the duct. Repeat the problem for fluid particles originally along line C-D; along line E-F. Compare your three answers. B F V = 20 m/s 0.5 m 60° A A' C E Figure P4.62

4.62 (wILEYo Water flows through a duct of square cross section as shown in Fig. P4.62 with a constant, uniform velocity of V = 20 m/s. Consider fluid particles that lie along line A-B at time 1 = 0. Determine the position of these particles, denoted by line A'-B', when t = 0.20 s. Use the volume of fluid in the region be- tween lines A-B and A'-B' to determine the flowrate in the duct. Repeat the problem for fluid particles originally along line C-D; along line E-F. Compare your three answers. B F V = 20 m/s 0.5 m 60° A A' C E Figure P4.62

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3: In Figure 3, W is the block weigh, which slides down a lubricated inclined plane. Supposing a linear velocity distribution in the film, derive an expression for the (zero- acceleration) velocity V of the block. Assume the film contact area is A and its thickness is h. Liquid film of thickness h Figure 3 Block contact area A
Q3. In the two dimensional situation shown, the following quantities are given: u = 50, v, = 20, PN =0, PE =10.The flow is steady and the density is uniform. The momentum equations for u, and v, VN are given by: u=d. (PP-PE) v=d, (PP-PN) where the constants d and d, are given by d = 1, d, = 0.6. The control volume shown has Ax = Ay. Use SIMPLE algorithm to obtain the values of u, V and pp. W 3 Ax N n P S S e Ay E
Fluid mechanics
A Newtonian fluid is flowing in the narrow gap between two infinite parallel horizontal plates due to the movement of the top plate (see the figure below). The top plate is moving at a speed U from left to right, and the bottom plate is stationary. Consider the flow is steady, incompressible, and laminar. The distance between two plate is H, and the gravity acts in negative z-direction (which is perpendicular into the page). There is an applied constant pressure gradient of apJəx in the x-direction. Calculate the velocity and pressure fields. Plot typical velocity profiles in dimensionless form for a pressure gradient value of 0 and -15. In your solution show the conceptual diagram of the problem; write all relevant assumptions and boundary conditions; show the detailed steps of the problem solutions including equations and detailed processing of those equations. Moving plate Fluid: p.H Fixed plate P2-P1
For the flow of an incompressible fluid, the velocity in x-direction u ax by and velocity in z direction is zero. Find volocity component in y-direction such that v = 0 at y = 0.
I need the answer as soon as possible
In plane stagnation flow, an incompressible fluid occupying the space y>0 has one velocity component given by Vx-x. The flow is two-dimensional and steady, such that V₂=0 and nothing depends on z or time t. (a) Use the continuity equation to determine Vy(x,y), given that Vy(x,0) =0. (This condition for Vy corresponds to the plane y=0 being an impenetrable boundary.) (b) is arbitrary, so you may set Y=0 at any convenient location.) Determine the stream function for this flow, (x,y). (The absolute value of
In a stream line steady flow, two points A and B on a stream line are 1 m apart and the flow velocity varies uniformly from 2 m/s to 5 m/s/ What is the acceleration of fluid B?
3.14. Find the vorticity in polar coordinates for the following velocity com- ponents (a) v=rsin 0, ve = 2r cos 0 (b) v = cos 0, 11=0
Please help me with this question with details. i need answer of these questions with explanation.
(b) A jet of water 500 mm in diameter with a velocity of 20 m/s strikes a flat plate inclined at an angle 0 to the axis of the jet as shown in Figure Q2 (b). Determine the angle 0 as the anchoring force, FĄ is 6000 N.
Lubricating oil is pumped to flow with velocity, V between two stationary paralle! plates separated by a thin gap of b = 1.8 mm as shown in Figure Q4. The gauge pressure at the inlet, Pn, is 100 kPa gauge. The pressure changes linearly to the atmospheric pressure at the outlet. Assuming the oil as an incompressible, steady and fully developed laminar flow of viscous fluid, detemine the equation of the velocity profile and the volume flow rate, Q. Calculate the Reynold number for the flow to justify that the flow is indeed laminar. [Lubricating oil properties: µ = 72.5 x 10° kg/m.s and p = 865 kg/m³] 1.0 m Pin y Pout 0.8 m V Figure Q4