+Google dasx Machine design -و واجب تصعية.pdfكيفية حساب نسلك لوحة مستطيلة xتصميم عناصر الهاكنة1 ثالث م xx Machine Design - Eng.C:/Users/MI/Desktop/i20%als-pdfLCD Custom Charac. OShare | Home Page OB الفصول الدراسية تحويل JPG إلى .- PDFYouTubeGmail M100%3/ 2واجب تصمیم.pdf4.6 The stresses induced at a critical point in amachine component made of steel 45C8 (S= 380 N/mm?) are as follows:;= 100 N/mm? 0,=40 N/mm?Ty= 80 N/mm?Calculate the factor of safety by (i) themaximum normal stress theory, (ii) themaximum shear stress theory, and (iii) thedistortion energy theory.[(i) 2.44 (ii) 2.22 (iii) 2.32]09:43AR

4.6 The stresses induced at a critical point in a machine component made of steel 45C8 (S, = 380 N/mm2) are as follows: O, = 100 N/mm² o,=40 N/mm2 T,= 80 N/mm2? Calculate the factor of safety by (i) the maximum normal stress theory, (ii) the maximum shear stress theory, and (iii) the distortion energy theory. [) 2.44 (ii) 2.22 (iii) 2.32]

4.6 The stresses induced at a critical point in a machine component made of steel 45C8 (S, = 380 N/mm2) are as follows: O, = 100 N/mm² o,=40 N/mm2 T,= 80 N/mm2? Calculate the factor of safety by (i) the maximum normal stress theory, (ii) the maximum shear stress theory, and (iii) the distortion energy theory. [) 2.44 (ii) 2.22 (iii) 2.32]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stresses at a point in a bar are o1 = 28N/mm2 (tensile) and o2=12N/mm2 (compressive) as shown in Figure (a) Determine the normal, tangential and resultant stress in magnitude and direction on a plane inclined at 55° to the axis of the major stress. (b) Determine the maximum intensity of shear stress in the material at the point. (c) Also, solve the same problem using Mohr's circle method and compare the results. O2 Axis of Major Stress 55°
A circular steel tube of length L = 59 inches is loaded in torsion by torques T (see the figure). r2 (a) If the inner radius of the tube is ri = 1.35 in. and the measured angle of twist between the ends is p = 0.5°, what is the shear strain y1 (in radians) at the inner surface? Round your answer to nearest whole. x10-6 rad Yi = (b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to be kept at 0.5° by adjusting the torque T, what is the maximum permissible outer radius (r2).may? Round to two decimal places. (r2)max in.
An aluminum pipe (modulus of elasticity 10.1x10^6 psi) is fixed at one end and is subjected to a tensile load of 127.5 kips at the free end. The length and cross-sectional area of the pipe is given as 36.1 in and 9.11 in^2. Assume that the aluminum pipe has clockwise torques (100 lb-in) acting at the midpoint and free end of the pipe. (a) Derive the element stiffness matrix
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in bronze bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 144.21 102.49 341.33 54.56
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P (Newton) that will not exceed a stress in steel of 147 mPa. in aluminum of 94 mPa, or in bronze of 109 mPa. The final answer should have 2 decimal places where cross-sectional area of Steel = 513 mm2; Aluminum = 416 mm2; Bronze = 207 mm2 Length of Steel = 3.0 m; Aluminum = 2.7 m; Bronze = 1.8 m
The tension element in the figure represents the state of tension at a given point. Calculate the principal stresses and the absolute maximum shear stress.
Mechanics of deformable bodies -Write complete solution
4
The beam shown in Fig QB1 is made from aluminium tube of rectangular cross-section having a vertical height of 50mm, a horizontal width of 30mm and a wall thickness of 3mm. The dimensions given in the figure are in millimetres. The yield stress in tension is 200MPa; Young's modulus is 71GPa. Determine: an expression for the bending moment at every point in the beam and draw the bending moment diagram a) b) c) d) the maximum bending moment the maximum longitudinal stress the maximum vertical deflection 200 3kN 200 1kN 100
A load of 1000 N is applied as shown in figure, given cross-sectional area of bar 1 & 2 is 100 mm² & 80 mm2, young modulus of elasticity E₁ = 120 GPa, E₂ = 150 GPa. Calculate the minimum normal stress (in MPa) (1) (2) P= P= 1000 N
A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a tensile axial force P, its diameter is decreased by 0.018 mm. Assume the Poisson’s ratio to be 0.33. Determine the value of loads P and its axial deformation. P = ? N δ = ? mm
44 ksi 3 ksi 70 S ksi Given the state of stress above (ignore 70° plane): calculate the maximum shear stress, maximum principal stress and minimum principal stress in this order. Choose only one answer.