و واجب تصصيم.pdfx 21- ale - la ay de aLisyae li leslal aie paai Bx Machine Design - Eng. Peter - SeC:/Users/MI/Desktop/i20%als-pdfLCD Custom Charac. OShare | Home Page OB الفصول الدراسية تحويل JPG إلى .- PDFYouTubeGmail M100%3 / 1واجب تصميم.pdf4.5 The principal stresses induced at a point ina machine component made of steel 50C4(Sy = 460 N/mm2) are as follows:Oj = 200N/mm²Calculate the factor of safety by (i) themaximum shear stress theory, and (ii) thedistortion energy theory.0, = 150 N/mm? 03 =0%3D[(1) 2.3 (ii) 2.55]09:35AR

Given: σ1=200 N/mm2σ2=150 N/mm2σ3=0

4.5 The principal stresses induced at a point in a machine component made of steel 50C4 (S, = 460 N/mm2) are as follows: oj = 200N/mm? O2=150 N/mm? 03 =0 Calculate the factor of safety by (i) the maximum shear stress theory, and (ii) the distortion energy theory. (6) 2.3 (ii) 2.55]

4.5 The principal stresses induced at a point in a machine component made of steel 50C4 (S, = 460 N/mm2) are as follows: oj = 200N/mm? O2=150 N/mm? 03 =0 Calculate the factor of safety by (i) the maximum shear stress theory, and (ii) the distortion energy theory. (6) 2.3 (ii) 2.55]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

K=17 so 107 MPa strength of material question.
The stresses on the surface of a hard bronze component are shown in the figure below. The yield strength of the bronze is σY = 345 MPa.a) What is the factor of safety predicted by the maximum-shear-stress theory of failure for the stress state shown? Does the component fail according to this theory?b) What is the value of the Mises equivalent stress for the given state of plane stress?c) What is the factor of safety predicted by the failure criterion of the maximum-distortion energy theory of failure? Does the component fail according to this theory?
Q1B
answer as soon as soon as possible
A steel bar, the material of which is S355 J2 G3, binds two walls together. Pre-tensioning in tie bar 4.3 kN. The temperature of the rod increases by 15 °C. Calculate the normal stress in the cross section of the bar. L = 600 mm, α = 12μ 1/°C, E = 200 GPa and d = 25 mm . Give the answer in MPa as a whole number as a numerical value only. Correct answer to exercise should be = -27
3. Assume the plane stress state: ơ1 = 0, 02 = 20, T12 = 15 (all stresses in ksi). If oz alone is increased until the maximum shear stress t1, in the material reaches ±20 ksi, what is the value of o, at this point? HINT: this is relatively easy to figure out if you construct a Mohr's circle for the initial stress state and then consider what happens if o, is replaced with Ao2 and you solve for A when the maximum shear stress (from the circle geometry) reaches ±20 ksi.
Q5: As shown in Figure (4.16), the maximum shear stress at section (a-a) is (29.47 MPa). If (b =12 mm), (r-250 mm),(G-84 GPa). Find: 1) The torque T, and 2) The angle of rotation at section -b). (b 3T 1m 0.9 m 0.6m
P2.12 (WP A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the right by u = 0.8 mm and upward by v = 1.3 mm to new position Q', as shown in Figure P2.12. Determine the shear strain y at corner Q' after deformation. Use a = 225 mm, b = 455 mm, and d = 319.96 mm. v7 d FIGURE P2.12
AL: 1₂ The above figure (not drawn to scale) shows a rod made up of two cylindrical sections of the same material. The left cylinder has diameter d, = 30mm and length 4 = 150mm. The right cylinder has diameter dy=10mm and length = 150mm. The rod is subjected to a force F = 50KN. Find the total extension in the rod, AL, given that E = 203kN/mm². Enter your answer in mm to 5 decimal places in the box below: mm -F
Q2 The shaft in Figure Q2.1 consists of three sections of different diameters and shear moduli as shown. It is fixed to a wall at A and loaded at points B.C and D. GAB 50 GPa dAB = 60 mm 30 kNm ++ 0.1 m Q2 contd. B ** GRC = 70 GPa dac = 80 mm 0.2 m Fig. Q2.1 Gcp= 50 GPa dep 40 mm C 20 kNm Fig. Q2.2 0.1 m D (a) Draw the Torque diagram for the shaft AD. Show all of your working and indicate all key values. (b) Determine the angle of twist for each section of the shaft (AB, BC and CD) and the total angle of twist between A and D. 5 kNm (c) If the shear strength for the entire shaft is 400 MPa, determine the maximum torque each section can withstand. Ø 120 mm 3 bolts equally spaced MEE1004/2021 (d) The shaft is to be fixed to the wall at end A via a flange with 3 equally spaced bolts, on a pitch circle diameter of 120 mm, as shown in Figure Q2.2. If the bolt material has a shear strength of 300 MPa, determine the minimum diameter of the bolts.
Need Help With This Question
Q2(c) The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c). If the allowable shear stress of the shaft is 80kPa, i)Determine the maximum torque T that can be transmitted by the shaft. ii)What would be the maximum torque T' if a 25 mm diameter hole is bored through the shaft? Figure Q2(c.) |Q2 c) (i) T c The torsion formula :7 = J Т (0.019) T (0.019)^4 ; Therefore, the max torque T = x10 Nm 80 2 Q2 c) (ii) For point lying on the outside suurface of the shaft: x10 ="(0.019) * (0.019*-0.0125 ) ; Therefore the max torque T' Nm 80 2 Q2 c) (iii) The shear stress at point located at inner surface of shaft, T'c T = -= J ) (0.0125) = 7 (0.019*-0.01254) T'c kPa 4. 2 2.