Please solve question 4.44 attached below, Thank You! 4.44 Consider the 2-degree-of-freedom system defined by:[1929] * + [1² 3-33x = 0Use modal analysis to calculate the response of the system to the initial conditions: x = 0and Xomm

The equation of 2 degree of freedom is defined by The initial condition are

Answered: 4.44 Consider the 2-degree-of-freedom…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure Q1c shows a bracket on rollers that allow the bracket to move along a beam in the horizontal direction. A force F₁ of 2625 N acts at point A where the angle between F₁ and the x-axis is 100. If force F2 acts at an angle a = 40° between F2 and the y-axis: (1) (ii) Give your answers to the nearest newton (N) to 2 decimal places. Assume coplanar forces and assume horizontal rolling is frictionless. Determine the magnitude of F2 necessary to maintain bracket on horizontal equilibrium. Determine the vertical force at A acting along the y-axis. F1 0 y α Figure Q1c F2 X
After years of asking, you finally were allowed to go on a joy ride in your uncle’s 1956 Mercedes-Benz 300 SL. A notable feature of this vehicle is the gullwing door design that opens from a hinge at the top of the car. Unfortunately, you are having so much fun driving the car that you end up submerged in a fresh water lake. You sink to the bottom of the lake, which has a depth of 10 m. For the sake of simplicity, you can model the door as a 1 m × 1 m square plate, inclined at 45° relative to the floor of the lake. Neglect the weight of the door and friction in the hinge. How much force will be required to open the door, assuming you push from its geometric center?
15° Deltoid 17 cm 38 cm A young girl is holding her arm straight out parallel to the ground. Her arm is perfectly straight. Use the information given in the picture and below to solve problem 2. a) Draw and label the free body diagram of all forces on the shoulder b) Calculate the force of the deltoid using the sum of the moments. c) Find the vertical reaction force of the shoulder. Is it acting "up" or “down" לי Weight of the arm = 1[kg]
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
2.22 Calculate the centre distances for a v-belt drive given pulley pitch diameters of 180 mm (motor) and 400 mm (driven) when the belt is (a) an SPÁ 2 360; and (b) an SPB 3 800. [716 mm; 1 441 mm] Calculate the angle of contact on the smaller pulley for both cases. Determine the tension ratio if the groove ang- les are 38° and u is 0,25. (162°; 171
Please I want you to solve the question below in the same way that I provided in another. picture I want to you to include F_R. also the coordinator x_R and YR. and x_C and y_C. also I want to know the h_C. The gate in the figure below is 5 ft wide, is hinged at point B, and rests against a smooth wall at point A. (1) Compute the force on the gate due to water pressure (Must include the magnitude and the center of pressure) (2) Compute the horizontal force exerted by the wall at point A. (3) Compute the reaction force at the hinge B (Must include the magnitude and direction
Need help with these Q2. Identify any zero force members. ( there can be more than one ) Member AB Member AJ Member BCBC Member BH Member BJ Member CD Member CG Member CH Member DE Member DF Member DG Member EF Member FG Member GH Member GJ q3. You are asked to find the forces in members GHGH and CGCG using the Method of Sections. Which members should you make a cut through? Member AB Member AJ Member BC Member BH Member BJ Member CD Member CG Member CH Member DE Member DF Member DG Member EF Member FG Member GH Member GJ Q4. Having made a cut through the members in the previous part, you next want to solve for Member GH. Which of the following equilibrium equations is the most efficient? (i.e. which one will allow you to solve for the required member in one equation?) a. ΣFx=0. b. ΣMC=0. c. ΣMH=0. d. ΣFy=0 e ΣMD=0
Assume the image below is your arm and you are lifting a 15 lb weight. your arm is now at a 50-degree angle to your body. The force from the muscle is vertical. The weight of your arm is 5 lbs. dbiceps is 2cm and dball is 6cm. Please draw a free body diagram of the arm at that 50-degree angle with the forces. What is the force that the muscle puts on the arm? What is the force from the muscle if the weight is all the way up?
P235 - The gate below is an isosceles triangle with 3m side. What is the proper configuration, the triangulate upright or inverted, so that the forces are as minimal as possible? - What would the forces be like in a circular 3m radius floodgate?
Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

4.44 Consider the 2-degree-of-freedom system defined by: [2]+[233] x=0 3¾ X= Use modal analysis to calculate the response of the system to the initial conditions: x = 0 1 and Xo = mm 2