4.41) If the Q- factor of a coil at resonant frequency of 1.5 MHz is 150 for a series resonant circuit, then the corresponding bandwidth is (a) 225 MHz (b) 1.06 MHz (c) 50 kHz (d) 10 kHz

Q: • Draw the relation between frequency and e

A: We need to find out the relationship between angle and frequency .

Q: Usually, a multistage amplifier connection can

A: Amplifier An electronic device or we can say circuit arrangement in which for small amplitude signal…

Q: Determine the impedance of the circuit in Figure (4.b) at the resonant frequency fr 17.794 KHz %3D…

A:

Q: frequency of resonance.

A: Resonant frequency

Q: current and impedance

A:

Q: how would you explain the operation of JKFF circuit for the frequency division by 8?

A: Flip-flop Flip-flop is an elementary memory type of element. It can store 1-bit of information. It…

Q: Calculate the bandwidth in kHz Blank 1 and an inductor's Q Blank 2 at100MHz. It has an inductance of…

A: Bandwidth is the difference between the upper cut-off frequency and the lower cut-off frequency.

Q: attenuation

A:

Q: How many decades are between f 1 =20 Hz and f2 = 4.5 kHz.a. How many octaves?

A:

Q: I Ic Rc=1000 RL C=100µF

A: We know the condition for infinite number of resonance frequency

Q: 5.12 For a series RLC resonant circuit, what is the total reactance at the lower half power…

A: we need to determine total reactance at the lower power frequency.

Q: What is the bandwidth of a signal that can be decomposed into five sine waves with frequencies at 0,…

A: Given: F1=0Hz, F2=20Hz, F3=50Hz, F4=100Hz, F5=200Hz To find Bandwidth

Q: H.W: A resistor of resistance R=1000 S2is maintained at 17 °C and it shunted by 100 uH inductor.…

A:

Q: Determine the break frequency in KHZ of the RC low-pass circuit below. Assume that Resistor value is…

A: break frequency is also called as cut-off frequency. resistance R = 3000 ohms capacitor C =  0.02 μF

Q: Determine the impedance of the circuit in Figure (4.b) at the resonant frequency f. = 17.794 KHz…

A: Frequency of the circuit is 17.794 kHz So w=2πf=2*π*17794=111803 rad/sec So impedance of the circuit…

Q: In a RC type low pass fitter, the cut-off frequency is 1500 Hz, Assuming the capacitance to be 500…

A: It is given that:

Q: 20. A 100 Ohm resistor, A 50 Ohm and 0.5 H coil, and a capacitor are connected in parallel to…

A:

Q: The resonant converter having fixed value of resonant frequency 48 Hz and capacitance of 2 muF. Find…

A:

Q: what frequencies will the output waveform be half-wave rectified? A full-wave rectified?

A:

Q: Bdc = B = 125 Cbc = 40PF Cbo =12PF Vc. p+12 V R1 12 RC 1.252 ,1µF 1 C2 RL 600 R5 502 R2 5 k2 * RE…

A: Low frequency response in the above circuit can be affected by coupling capacitor and resistor in…

Q: R=20k ww Rin=100kr Vin wm Vout C=100nF

A: The transfer function of the given circuit is calculated as:…

Q: The attenuation of a signal is -10 dB. What is the final signal power if it was originally 5 W?

A: Attenuation means degradation of output power with respect to the input power because of some losses…

Q: The frequency response of an LTI system is given by: H(w) = Find the time-domain output y(t) if the…

A: In this question we need to find the output y(t) of the given system for the following input is…

Q: Determine the output waveform: 10 5V -10+ 25+ 15+ (C) (A) (B)

A: Diode conducts when anode voltage is greater than cathode voltage and maintains zero voltage across…

Q: INSTRUCTION: USE 5 DECIMAL PLACES What value of R. will the circuit be in resonance given a parallel…

A:

Q: Determine the impedance of the circuit in Figure (4.b) at the resonant frequency f, = 17.794 KHz…

A: We need to find out the impedance of the given circuit at the given resonant frequency.

Q: |OLO° A R= 100 kQ L=20 uH %3D C = 5 nF

A: We need Analyse the given parallel resonance circuit .

Q: Q/ Graph the input and output wave of the following circuit R1 1kQ ADI V1 6.5 Vrms 50 Hz RL 10㎏Ω V2…

A:

Q: Question 3 A step-up chopper has input voltage of 225 V and output voltage of 385 V. If the non-…

A:

Q: A companding system with u = 100 used to compand from 0V to 10 V sinusoid signal. Draw the…

A:

Q: d. The peak voltage across the capacitor at resonance, fo e. The peak voltage across the capacitor…

A:

Frequency Modulation

Frequency modulation is a method or process of encoding the data of a specific signal (analog or digital) by modulating the carrier wave frequency according to the frequency of the modulated signal. Modulated signals are nothing more than information or data that should be conveyed after being converted into electronic signals.