4.30 Calculate the force in the tie rod BC and the reaction at the pinned support at point A for the rigid frame shown. B Pin 60° A 5'-0" 6'-0" 3'-0" SE e di ort W D = 1200 lb

Q: Given your understanding of what initiates and controls failure in materials, which of the following…

A: There are various methods by which we can  increase the failure strength and lifetime of a test…

Q: Please write down the fundamental law of gearing

A: Gears -  Gears are power transmission device, used to transmit power between two shafts. They are…

Q: b) With a neat sketch, identify and illustrate the metal forming processes for the following…

A: Forming, also known as metal forming, is a metalworking technique that involves the mechanical…

Q: In the paper mill, what six instructions lead to the manufacture of the design?

A: The specific six instructions that lead to the manufacture of a design in a paper mill can vary…

Q: What are assessments that measure strength, speed, agility, or high-speed strength? What are the…

A: The assessments that measure strength, speed, agility, or high-speed strength is T-Test

Q: Identify the type of forming process in which the material is required to pass repeatedly through…

A: Option c is correct.

Q: A material is required for a new product with fixed geometry that will be shaped by moulding. The…

A: When a material is selected to manufacture a material a lot of things are considered such as the…

Q: For a pitted specimen designated as A-3,B-3, and C-5(Figure 7.3), sketch the pit density, indicate…

A: The given standard chart provides a way in which pitting can be described. The given specimen is A-3…

Q: Materials, Properties and Testing Describe, with examples, the effect mechanical processes have on…

A:

Q: How is paper made?

A: GIVEN:   How is paper made?

Q: If you could perhaps offer a definition as well as an explanation of the idea of "expandability" in…

A: The ability of devices to be easily joined or merged with one another in order to enhance…

Q: Discuss the importance of print resolution and its impact on print quality.

A: Print resolution is a critical factor in determining the quality of printed materials, whether they…

Q: This is what I drew out. I'm unsure of hidden lines

A: Please refer the completed orthographic views of the given object. The drawing is made with the true…

Q: (a) There are three types of industry, primary, secondary or tertiary. i) ii) Briefly describe each…

A: a)(i)  Primary industry - Primary industries are the first players in manufacturing products that…

Q: In your own words, explain What are the properties that constitute physical change?

A: There are many types of changes that can be encountered on a material. These changes are related to…

Q: Explain in your own words the sentence; “engineering drawing is the graphic language of engineers.”…

A: given; Explain in your own words the sentence; “engineering drawing is the graphic language…

Q: When an airplane lands, the wheels of the landing gear first skid over the concrete landing strip…

A:

Q: Describe the effect that normalising has on material properties.

A: Normalizing:  It is a type of heat treatment process which is used to the ductility of any metal by…

Q: During plastic deformation anisotropy in sheet metals can: a have adverse effect during the…

A:

Q: determine the overall fraction of the operation.

A: In a two stage wire drawing operation,   the fractional reduction in the first stage is = 0.4…

Q: * Which defect arises due to small Punch force in sheet drawing operations? O Tearing O Wall…

A:

Q: 1. Once you have overdesigned your product, you need to do a to match the needs and capabilities of…

A: A customer need is a compelling reason for a consumer to buy a product or service. The need…

Q: You have been using pens and mechanical pencils for many years now. Investigate the design of at…

A: A pen is a common writing device that uses ink to write or draw on a surface, usually paper. Early…

Q: (a) Figure 1 shows surface roughness and tolerances obtained in Chemical Machining (CM) and…

A: Chemical machining and electrochemical machining

Q: In a metal forming industry, you are assigned to setup an equipment which is required to reduce the…

A: To reduce the cross-section of a bar from 100x50mm into 75x25 mm various forming processes can be…

Q: You have been using pens and mechanical pencils for many years now. Investigate the designs of at…

A: given: You have been using pens and mechanical pencils for many years now. Investigate the designs…

Q: What six instructions in the paper mill lead to the manufacturing of the design?

A: In the paper mill for the manufacturing of the paper design, there are several instructions or steps…

Q: Understand cohesive and adhesive forces.

A: The cohesion is defined as “the property of the molecules of a same substance attach together due to…

Q: Metal work: What are possible sources of error in trying to obtain a specific hardness or strength?

A:

Q: What would be the result of the Yielding of the material?

A: In stress-strain curve of material the yield point is the point of elasticity. Yield points shows…

Q: How to produce paper from ground nutshell ? Procedure?

A: Ground nutshell Groundnut organically known as Arachishypogeae has a place for a leguminous family.…

Q: If the amount of force applied on an object and its length is constant, how would you decrease…

A: When a member is subjected to an axial load, it experiences a change in its dimension. The ratio of…

Q: Processing of engineering materials. Discussion of various processing/techniques explain the…

A: Primary forming processes: It is a process under which the raw material convert into the industrial…

Q: 1. Explain the importance of standards and the principles of free hand in sketching in engineering…

A: The Answer is below

Q: 14 1. Wrinkling II. Tearing III. Earing IV. Surface scratches Which are some of the possible defects…

A:

Q: As shown in fig.(2). Prove the main equation for the coefficient of frictional force between the…

A:

Q: what is Deep Drawing?

A:

Q: What is the old and most recent technology of material removal Process

A: Metal removal processes use a metal cutting tool that moves relative to the workpiece, and removes…

Q: When does stress concentrations become important?

A: Stress concentration is very important in the case of cyclic loading. stress concentration leads to…

Q: Comparison factor Volumetric deformation Sheet metal work Surface area/volume ratio: High, Low Basic…

A: comparison factor  volume deformation  sheet metal work surface area/volume ratio; the area of…