4.22 A laser diode has a maximum average outputof 1 mW (0 dBm). The laser is to be amplitude-modulated with a signal x(f) that has a dccomponent of 0.2 and a periodic componentof ±2.56. If the current-input to optical-output relationship is P(t) = i(t)/10, find thevalues of /, and mif the modulating current isi(f) = l, [1+ mx(t)].

Given, A laser diode has maximum average output of 1 mW (0 dBm) Signal x(t) has a dc component of…

4.22 A laser diode has a maximum average output of 1 mW (0 dBm). The laser is to be amplitude- modulated with a signal x(f) that has a de component of 0.2 and a periodic component of ±2.56. If the current-input to optical- output relationship is P(t) = i(t)/10, find the values of /, and mif the modulating current is i(t) = I, [1+ mx()].

4.22 A laser diode has a maximum average output of 1 mW (0 dBm). The laser is to be amplitude- modulated with a signal x(f) that has a de component of 0.2 and a periodic component of ±2.56. If the current-input to optical- output relationship is P(t) = i(t)/10, find the values of /, and mif the modulating current is i(t) = I, [1+ mx()].

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

c.1 Given that apc = 0.980, determine the corresponding value of Boc: c.2 Given Bpc = 120, determine the corresponding value of a. c.3 Given that Boc = 120 and IC = 2.0 mA, find IE and IB. %3D %3D %3D
piscussion:- 1. Sketch Vo 20 V -20 v 2. Design a diode clamper to generate the Vo fromV 10v 2.7V UNIVERSITY - L0v -17.3
(1) For the circuit shown, assume that the diode voltage during on-time is 0.7V. Obtain and draw the voltage v, if the input voltage v, is as follows: D4. (a) A square wave with an amplitude of±10V and frequency of 20HZ is applied to the circuit below. (b) A sinusoidal voltage with an amplitude of 2V and frequency 10HZ.
6V -10 For the Given and input waveform determined the output waveform a) c) d)
Vprip ~ Vgiris Voltage-Time relationship in the signal first half cycle of the doubler circuit and the wM A w A wA direction of current flow on the circuit. For the input voltage, give a sine signal with a frequency of 10Vp-p 1kHz . Use a value of 1µF for the capacitor. For diodes, use an ideal diode by making VD = OV. Obtain and report the output voltage in graphical and tabular form. Find the output voltage.
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Electronic lab
double clipper circuit Zener diodes 1N4733A has a voltage of 5.1 V and 1N4735A has a voltage of 6.2 V with a resistor R=300ohms has been used. you may like to increase the input to a 12 VRMS AC source in order to see the clipping at 7volt. Please, Do the theoretical calculations and plot the expected waveforms by hand. ( I have its multisim design and only needs theoretical calculation and hand drawn graph of it to compare to its data that I have collected from multism.) Thanks
Determine the noise current for a diode with a forward bias of 1mA over a 100 kHz bandwidth. If the diode is in a circuit with 5002 series resistance, calculate the total output noise voltage at 27°c. (from miller: In = 0.00566µA, total noise voltage = 0.154 µVrms) %3D
1.Find condition to know Diode on or off, Von = 0.7V. 2 Find relative equation between Vo and Vin
Using a positive Clamper with positive biasing voltage Circuit, with an AC voltage of Vi = 20v with a frequency of 60hz, a value of 500n for the Capacitor, a silicon diode, biased voltage voltage of 5 volts and a resistor with the value of 300 ohms. Find the current on the resistor at a simulation of 20ms in mA. Vm 2Vm R V,m Vo -Vm V, Input Waveform Output Waveform Positive Clamper with positive reference V, www
4. For the following waveforms, construct a Zener wave-shaping circuit. Include the working principle of the circuit with proper ratings. t 18.