4.17.) The volume of a compressible fluid system changes from V, = 1 ft³ to V2 = 5 ft3 duringan internally reversible process in which the pressure varies a p = (100/V + 50) psia when V is inft3. (a) For the process find -S Vdp and SpdV. (b) If the process is steady flow with AK = 5 Btu,AP = -2 Btu and AH = 120 Btu, find the work and heat. (c) If the process is nonflow, find W, Qand AU.

Answered: Image /qna-images/answer/512fa539-343d-446b-b231-a6f5a9efc038.jpg

4.17.) The volume of a compressible fluid system changes from V, = 1 ft³ to V2 = 5 ft³ during an internally reversible process in which the pressure varies a p = (100/V + 50) psia when V is in ft³. (a) For the process find -S Vdp and SpdV. (b) If the process is steady flow with AK = 5 Btu, AP = -2 Btu and AH = 120 Btu, find the work and heat. (c) If the process is nonflow, find W, Q %3D and AU.

4.17.) The volume of a compressible fluid system changes from V, = 1 ft³ to V2 = 5 ft³ during an internally reversible process in which the pressure varies a p = (100/V + 50) psia when V is in ft³. (a) For the process find -S Vdp and SpdV. (b) If the process is steady flow with AK = 5 Btu, AP = -2 Btu and AH = 120 Btu, find the work and heat. (c) If the process is nonflow, find W, Q %3D and AU.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

answer in complete solution.
Q3: _A- 0.5kg/s of a fluid flows in 2 steady state process. The properties of fluid at entrance are measured as pl = 1-4bar, density = 2Skg/m3 , ul = 920ki/kg while at exit the properties are p2 = 5.6 bar, density = 5 kg/m3 , u2 = 720kd/kg. The velocity at entrance is 200 m/sec, while at exit itis 180m/sec. It rejects 60kw of heat and rises through 60m during the flow, Find the change of enthalpy and the rate of work done,
Q 1: For a particular gas system, the internal energy is given by : U = 2.5 PV + C , where P: Presure , V: volume and C : constant, the sysytem is taken into cycle shown in fig.(Q1) below with three Processes, Calculate Q & W if the pressure is given by P= 105 + 10° (v-0.02)² ? 0.5 0.4 0.3 0.2 B A 0.1 001 002 003 V (m³) -> Fig. (Q1) P (MPa)►
Q2) Find: (a) initial pressure (P, =?). (b) final temperature (T, =?), (C) the amount of heat added to the system, (d) plot T-r and P-r diagrams. Water: m =2 kg V1 =V, = 30O L Qm =? T= 120°C P,- 1.8 MPa
This fixed-mass system undergoes an isothermal, quasi-equilibrium process from state 1 to state 2. The initial volume is 1 m^3. The mass inside the system is an unspecified ideal gas. Initial Pressure starts at 1000 kPa and the final pressure goes to 100 kPa. Find the change in specific internal energy the work done on the system and the heat transfer in KJoules.
Include simple schematic , process digram , and assumption
Use the deal gas law to find the temperature rise/drop in the air (M = 18.57 kg/kmol) for the constant pressure from the atmospheric conditions (p = 100 kPa, T = 15 degrees Celsius) To v2 = 0.6 m^3/kg The universal gas constant is 7.123 kj/kmol K 0 degrees Celsius = 273.16 K
Q5: What is heat transfer? And modes oh heat transfer?
H.W: - 0.8m of gas at 8bar and 27°C is compressed isothermally until its volume is ¼ time the original volume, then its heated at constant pressure to original volume, finally its cooled at constant volume to original condition. Find: - a- the heat transferred. b- Work done c- Change in internal energy. (draw the processes on p-v diagram) Take cp=1.01kj/kg.k, R=0.28kj/kg.k
b) Elaborate the response of pressure to the reservoir fluid properties using suitable equation.
i need the answer quickly
Momentum Transfer. Answer the ff.