4.15 An audio signal has a bandwidth of 15 kHz. The maximum value of |m(t)| is 10 V. This signal frequency modulates a carrier. Estimate the peak deviation and the bandwidth of the modulator output, assuming that the de- viation constant of the modulator is (a) 20 Hz/V (b) 200 Hz/V (c) 2 kHz/V (d) 20 kHz/V

4.15 An audio signal has a bandwidth of 15 kHz. The maximum value of |m(t)| is 10 V. This signal frequency modulates a carrier. Estimate the peak deviation and the bandwidth of the modulator output, assuming that the de- viation constant of the modulator is (a) 20 Hz/V (b) 200 Hz/V (c) 2 kHz/V (d) 20 kHz/V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem 1 The Figure below shows a screen shot of a signal recoded by an oscilloscope. a) What are the average and fundamental frequency for the given signal? b) If the signal is sampled with a sampling frequency of 10 Hz, sketch the sampled signal on the same chart. c) Find the average value of the sampled signal. d) Use zero-order hold to convert the sampled signal to a continuous one and sketch your result on the same chart 2. 0.5 0.4 Time (s) 0.1 0.2 0.3 0.6 0.7 0.8 0.9
B) The following waveform is the RB (return to bios) representation of the serial digital data, find the digital data code and draw the NRZ (non-return to zero) and RZ (return to zero) waveforms. C) The waveform below is the PAM for the analog signal, draw the analog signal, PWM and the PPM for this signal. 12
a) Determine the output voltage for all input voltages values. b) Sketch the overall output waveform, Vo(t).
7-22 Abasehand signal with frequency components from near de to 15 kHz frequency modulates a 200-kHz carrier, and the frequency deviation is +3 kHz. The signal is applied as the input to a cascade of two frequency triplers and one frequency doubler. Determine the output (a) center fre- quency, (b) frequency deviation, and (c) deviation ratio.
The circuit is shown below, Vin is the sinusoidal waveform with magnitude 5V and frequency is 100 Hz, R = 1 k, C = 1 uE, the chip is supplied by + 12 V source. a) What is the waveform of Yout? b) Calculate the magnitude of Vo c) If Vin is triangle waveform, what is the output waveform? -Vout , if Vin is triangle waveform with magnitude of 5 V (peak-to-peak value is 10 V) and frequency is 10 kHz, calculate waveform of you and the magnitude of I/?
Digital Electronics and Design Questiona) Write a 2:1 MUX module using Verilog-HDL.b) Use the module in (a) and write a Verilog-HDL code to implement a 4:1 MUX.
6. Consider the electrical circuits shown in figure a.) and b.). For each circuit determine the transfer function C/2 C12 2R 2R (a) R (b)
Assume a signal is represented by the following expression, Calculate: a)The signal bandwidth in KHz. Show all calculation steps. b)The period of the fundamental frequency in micro sec. Show all calculation steps.
Please Solve this Question: Design a Relaxation oscillator (using 1 OPAMP, 3 resistors and 1 capacitor) togenerate a square waveform of period 220us and 50% duty cycle.
a.Derive the excitation equations b. Determine transition and output equations c. Derive the transition/output table and Draw the state diagram.
Explain the data rate (bps), symbol rate, bandwidth and noise. What are the relationship amongthem.