4.131 Water flows steadily through the double elbow shown in Fig. P4.131. Water flows into the elbow from the top at 5 m/s, and from the left at 15 m/s. Determine the vertical and horizontal components of the force needed to hold the elbow in place. V2 = 5 m/s 45 cm P2 = 30 kPa P = 250 kPa %3D 25 cm V = 15 m/s P3 = 170 kPa %3D 20 cm V3 40° Fig. P4.131

4.131 Water flows steadily through the double elbow shown in Fig. P4.131. Water flows into the elbow from the top at 5 m/s, and from the left at 15 m/s. Determine the vertical and horizontal components of the force needed to hold the elbow in place. V2 = 5 m/s 45 cm P2 = 30 kPa P = 250 kPa %3D 25 cm V = 15 m/s P3 = 170 kPa %3D 20 cm V3 40° Fig. P4.131

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Consider the following piping system, which has a mass flowrate of 12 kg/s: Liquid level 4.1 m Open to Atmosphere Storage Tank Disuction=4.026-inch Pump 0.6 m e suction 65J/kg e discharge 555 J/kg Discharge 3.068-inch 1.2 m Determine the velocity in the discharge side. e. Determine the velocity on the suction side. f. Determine the pressure at Point 3 (the inlet to the pump). Pressure in Vessel = 3.4 bar = 3.4×105 Pa 5.8 m g. Determine the work required for the pump (which is 65% efficient). h. Determine the pressure at Point 4 (the discharge of the pump). Liquid level 2.9 m Process Vessel
4.68 The wind blows across a field with an approximate velocity profile as shown in Fig. P4.68. Use Eq. 4.16 with the parameter b equal to the velocity to determine the momentum flowrate across the vertical surface A-B, which is of unit depth into the paper. 10 ft 15 ft/s Figure P4.68 20 ft 2017- S SATIN Har
Q3. In the two dimensional situation shown, the following quantities are given: u = 50, v, = 20, PN =0, PE =10.The flow is steady and the density is uniform. The momentum equations for u, and v, VN are given by: u=d. (PP-PE) v=d, (PP-PN) where the constants d and d, are given by d = 1, d, = 0.6. The control volume shown has Ax = Ay. Use SIMPLE algorithm to obtain the values of u, V and pp. W 3 Ax N n P S S e Ay E
4.129 For the system shown in Fig. P4.129, estimate the downstream pressure p2 if p1 V1 = 20 m/s. Neglect losses. (Note: The pressure immediately after the pipe expansion is p1.) 30 kPa and | P2 P1 6 cm dia. Water V1 V2 3 cm dia. Fig. P4.129
4.5 The water flows in a 4m wide canal at a velocity of 5 m/s. A wedge-shaped column bifurcates the stream, as shown in Fig. 4.29. Calculate the force per unit depth exerted by the water stream on the column, if the wedge angle (a) is 30°. V=5m/s V=5 m/s V=5 m/s Fig. 4.29 [Ans: 3407.4N]
If anyone can help with this problem I would appreciate it. Thank you! Answers listed in the book are: a) 5, (b) 4.4 m/s, (c) −ρV 22 H2w((1 + cos θ)i + sin θj), (d) magnitude ×1/4
Subject : Mechanical engineering ,Fluid mechanics. Question: A stream of water 75 mm in diameter discharges into the atmosphere at a velocity 24.4 m/s. Find the power in the jet using the datum plane through the center of the jet. Answer is 33 kW
Please assist me with this question as soon as possible.
Q4: A centrifugal pump running at 900 rpm and delivering 0.3 m³/s of water against a head of 25 m. The flow enters the vans radially, the normal velocity of flow through impeller is constant and equal to 3 m/s. If the pump efficiency is 82% determine the diameter and width of the impeller. The blade angle at outlet is 25°
An object is projected vertically upwards with velocity 50 m/s. Find: The height it reaches ( Take g = 10 m/sq s ) LAWS=13.56M/S
Question / Calculate the critical design loads applied to the Stirling Engine when in operation and provide a stress analysis on the piston .use a factor of safety of 5. Assume outside temperature (bottom plate) is -233 degC and an internal PC board (top plate) is 85 degC ? Figure 1.1 show measurement to help you