Please solve problem 4 only. Thank you so much CYLINDERS AND CONES IN PURE ROLLING CONTACT1. A and B are rolling cylinders connecting the shafts S and T. C and E are cylinders fast tothese shafts and slipping on each other at P. Find the diameters of C and E if the surfacespeed of E is twice that of C.PEAB162. Two solids of right section 2 and 4 are in pure rolling contact between the circular arcs.What is the angular speed ratio for the position shown? Determine the size of the angles a,B, and Ø in degrees, and of the radii x and y in inches.12-183. Two shafts, having axes in the same plate intersecting at an angle of 45°, turn in oppositesenses at 30 rpm and 90 rpm. Draw a pair of cone to be located on these shafts and turn inpure rolling contact. Diameter of base of smaller cone is 1 in. Calculate the cone angles.4. Two shafts A and B are connected by rolling cones and turn in the same direction. Shaft Amakes 300 rpm while shaft B makes 100 rpm. Calculate the cone angle of each cone andthe diameter of each base if the base of cone B is 2 in. from the vertex. 0 = 30°

Given: TO find the solution of the 4th question.

Answered: 4. Two shafts A and B are connected by…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You’re a Buyer at Tesla and just received 18,000 tires from Michelin. The floor has discovered an issue with the valve stem in 325 of the tires. What’s the PPM?
PLease answer this question, Thank you very much
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
An automotive company has employed you as a manufacture engineer to start a new unit. You are assigned with the production of the crank shaft piston assembly as shown in FIGURE Q1a. As an engineer responsible for producing the components shown in FIGURE Q1b, you have been asked to prepare a report with following details. Select the appropriate materials for the components shown in FIGURE Q1b.Propose the manufacturing processes that can be used to manufacture each of the components Crankshaft, power gears shown in FIGURE Q1b(i). Justify your selection of a particular manufacturing process. Discuss other alternative manufacturing methods and process variables that influence the properties of the components made. Suggest the manufacturing methods that gives near net shape for the connecting rod shown in FIGURE Q1b (ii).
what process is this? how to perform this? Procedure in position?
Write net torque and net force equation for a simple seesaw system
An automotive company has employed you as a manufacture engineer to start a new unit. You are assigned with the production of the crank shaft piston assembly as shown in FIGURE Q1a. As an engineer responsible for producing the components shown in FIGURE Q1b, you have been asked to prepare a report with following details. Select the appropriate materials for the components shown in FIGURE Q1b.Propose the manufacturing processes that can be used to manufacture each of the components Crankshaft, power gears shown in FIGURE Q1b(I). Discuss the selection of manufacturing process with reference to desired properties for connecting rod application. Recommend appropriate surface treatment methods for these parts as required by their application.
You have been tasked with designing a set of gears made from a material with a Brinell hardness (Hg) of 201 MPa. Previously your company has produced gears with a commercially polished surface finish, but your boss is interested in how much the bending strength would be decreased if a machined surface was used instead, with all other factors kept constant. Considering the surface factor figure and the AGMA equation for bending strength presented below, approximately what percentage decrease in bending strength (S,) would we expect to see changing from a commercial polished finish to machined surfaces? Hardness (Hp) 120 160 200 240 280 320 360 400 440 480 520 1.0 `Mirror-polished 0.9 Fine-ground or commercially polished 0.8 - Machined or cold-drawn 0.7 0.6 0.5 Hot-rolled 0.4 0.3 As forged 0.2 Corroded in tap water 0.1 Corroded in salt water 60 80 100 120 140 160 180 200 220 240 260 Tensile strength S, (ksi) St Sn = S'nCskrk¢kms O 28% O 20% O 23% O 7% Surface factor C,
Subject: Mechanical engineering
Provide and illustration to what is asked.
Make and Solve a problem involving the concepts of torsion Note: -Box the final answer
solve please

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

4. Two shafts A and B are connected by rolling cones and turn in the same direction. Shaft A makes 300 rpm while shaft B makes 100 rpm. Calculate the cone angle of each cone and the diameter of each base if the base of cone B is 2 in. from the vertex. 0 = 30°