4. The %Mn in steel can also be determined spectrophotometrically by oxidizing the manganese to the intensely colored permanganate, MnO4. Standard solutions of permanganate gave the following absorbances (in a 1 cm cell): ABSORBANCE CONC. OF MnO4 (g/mL) 0.210 1.05 x 10-5 0.315 1.61 x 10-5 0.429 2.21 x 10-5 0.599 2.98 x 10-5 0.801 4.04 x 10-5 The following samples of steel were thoroughly reacted to convert the manganese ir permanganate and then diluted to 500.00 mL. WT. OF STEEL (g) ABSORBANCE 0.5886 0.611 0.3498 0.359 0.4555 0.482 Again using Excel, plot the calibration data and calculate the %Mn in the steel.

4. The %Mn in steel can also be determined spectrophotometrically by oxidizing the manganese to the intensely colored permanganate, MnO4. Standard solutions of permanganate gave the following absorbances (in a 1 cm cell): ABSORBANCE CONC. OF MnO4 (g/mL) 0.210 1.05 x 10-5 0.315 1.61 x 10-5 0.429 2.21 x 10-5 0.599 2.98 x 10-5 0.801 4.04 x 10-5 The following samples of steel were thoroughly reacted to convert the manganese ir permanganate and then diluted to 500.00 mL. WT. OF STEEL (g) ABSORBANCE 0.5886 0.611 0.3498 0.359 0.4555 0.482 Again using Excel, plot the calibration data and calculate the %Mn in the steel.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

The molar absorptivity constant of a particular chemical is 2.31 M/cm. Determine the concentration of a solution made from this chemical that has an absorbance of 0.408 with a cell path length of 1.12 cm.
A solution of potassium permanganate of unknown concentration was analyzed against a standard of various concentrations. What is the concentration of KMNO4 if its absorbance is 0.678? Table 1. Data for the Standard Calibration Curve KMNO4 Standard Solution (mol/L) Absorbance at 525 nm 0.000400 0.112 0.000800 0.295 0.000120 l0.443 0.000160 0.701 0.00200 0.932 O 0.00173 M 0.00194 M O 0,00189 O 0.00155 M
You want to determine the amount of iron(III) in acomplex salt. You make a 100.0 mL solution of the complex salt by dissolving 0.0670 g of complex salt with water to the mark on a 100.0 mL volumetric flask. You get an absorbance reading for the iron from the spectrometer of 0.334. The molar absorptivity is determined to be 17605 L/mole∙cm and the pathlength is 1.00 cm. Determine the molarity of iron(III) in solution. Determine the mass percentage of iron(III) in the complex salt.
Blue Blue dye stock solution 0.293 M Absorbance at 630 nm 0.00265 Calibration curve y = 0.0833x A solution is prepared by diluting 2.81 mL of the blue dye stock solution to 25.00 mL. The measure absorbance for the prepared solution is listed in the data table. (a) What is the theoretical molar concentration? [Blue]theoretical | × 10 |M (b) What is the experimental molar concentration? [Bluelexperimental x 10 M (c) What is the percent error? Percent error (blue) =
The thickness of the chromium plate on an auto fender is determined by dissolving a 30.0-cm2 section in acid and oxidizing Cr3+ to Cr2O7 2-with peroxydisulfate. After removing excess peroxydisulfate by boiling, 500.0 mg of Fe(NH4 )2 (SO4 )2•6H2O is added, reducing the Cr2O7 2- to Cr3+ . The excess Fe2+ is back titrated, requiring 18.29 mL of 0.00389 M K2Cr2O7 to reach the end point. Determine the average thickness of the chromium plate given that the density of Cr is 7.20 g/cm3 . Note: thickness = volume /area
Absorbance measurements were taken on a series of Fe standards complexed with 1,10-phenanthroline. A plot of absorbance vs. concentration yielded a linear curve with the equation y=1.008e03x + 0.0395 (where y is the absorbance and x represents the Fe concentration in moles/L). Using this information calculate the Fe concentration (in ppm) in a 40.0-mL aliquot of ground water that produced an absorbance of 0.580.
What is the concentration of copper ions in a solution within a cuvette that has an absorbance value of 0.697 and a molar absorbtivity of 6.833 x 103 L/mol cm? The pathlength of the cuvette is 1.00 cm.
A mixture is prepared by combining 11.34 mL of 2.36 x 103 M Fe(NO3)3 with 10.00 mL of 1.66 x 10-3 M KSCN. The solution turns red due to the formation of FeSCN2+. The absorbance is measured and, using a calibration plot, the [FESCN2*] at equilibrium is found to be 2.20 x 10-4 M. Complete the following ICE table Fe3+ SCN 1t FESCN2+ initial (M) (A) (B) (C)0 change (M) (D) (E) (F) equilibrium (M) (G) (H) (1) What is the value of K?
The molar absorptivity of a compound at 500 nm wavelength is 252 M-1cm-1. Suppose one prepares a solution by dissolving 0.00140 moles of a solute in enough water to make a 500.0 mL solution. What would be the absorbance in a 7 .00 mm pathlength cell?
From experimental data, a plot of absorbance (in arbitrary units, a.u.) at a wavelength of 630 nm (on the y-axis) was plotted against the concentration (in mg/L) of Cu2+ (on the x-axis) in known solutions and a linear relationship was found with an equation of y = 7.22x+0.05. If an unknown solution had an absorbance of 1.20 a.u. at a wavelength of 630 nm, what is its concentration of Cu2+?
Significance of your results: Titanium is also commonly anodized, but does not need to be dyed to achieve colored surface layers. Instead, the color comes from thin-film refraction within the oxide layer - the color is characteristic of the thickness of the oxide layer. Ti²+ (aq) + 2e-Ti (s) E° = -1.60 V TiO₂ (s) + 4 H+ (aq) + 4 e-Ti (s) + H₂0 (1) E° = -1.076 V a. What is the half-reaction at the anode for the anodization of titanium? b. Under standard conditions, what is the smallest potential you would need to provide in order to anodize titanium?
The molar absorptivity for Blue #1 dye is 1.30105 M‒1 ·cm‒1 at 629 nm. Calculate the expected absorbance of solution of Blue #1 with a concentration of 4.50×10–6M when measured at 629 nm in a 1.50 cm cell.