Discuss and analyze the following results 41reduced.With the voltage applied to the lamp filament at 0V (control of the lamp voltageis via the 100kN carbon track resistor) as indicated on the Moving Coil Meter,move the slide resistor further to the right until the Solenoid changes state.Table 2LampFilamentVoltage236.710Slide ResisterSettinga.2 9.1 9 8-6 6.3 4.2 3.22.11.91.71.5> Adjust the lamp filament voltage to each of the settings given in Table 2 and repeatthe procedure noting the slide resistor setting required for change of state of theSolenoid. Record the results in Table 2.Control System Engineering- ELEC3000/METR3200

A table is provided with some values. These values are the results of a performed experiment. We…

4. reduced. With the voltage applied to the lamp filament at 0V (control of the lamp voltage is via the 100KN carbon track resistor) as indicated on the Moving Coil Meter, move the slide resistor further to the right until the Solenoid changes state. Table 2 Lamp Filament Voltage 1 2 3 8 10 Slide Resister a.2 9.1 9 8-6 6-3 4.2 3.2 2.11.91.71.5 Setting > Adjust the lamp filament voltage to each of the settings given in Table 2 and repeat the procedure noting the slide resistor setting required for change of state of the Solenoid. Record the results in Table 2. Control System Engineering- ELEC3000/METR3200

4. reduced. With the voltage applied to the lamp filament at 0V (control of the lamp voltage is via the 100KN carbon track resistor) as indicated on the Moving Coil Meter, move the slide resistor further to the right until the Solenoid changes state. Table 2 Lamp Filament Voltage 1 2 3 8 10 Slide Resister a.2 9.1 9 8-6 6-3 4.2 3.2 2.11.91.71.5 Setting > Adjust the lamp filament voltage to each of the settings given in Table 2 and repeat the procedure noting the slide resistor setting required for change of state of the Solenoid. Record the results in Table 2. Control System Engineering- ELEC3000/METR3200

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Electrical Engineering (a) Some polycrystalline photovoltaic cells are to be arranged to provide an output of 12V and a power of 120W. Design and sketch out the cell configuration that meets the specification, using a sketch. The datasheet shows that open-circuit voltage is 0.622V, short-circuit current is 8.XY A, and fill factor is 0.7Z. X=3 Y=2 Z=2
3. For the circuit, (i) Find the voltage vc and the current ic if the capacitor was initially uncharged and the switch is thrown into position A. (ii) Find the voltage vc and the current ic if the switch is thrown into position B. (iii) Plot the waveforms for the questions (i) and (ii) for both the voltage vc and the current ic. Mark the time constant for part (i) and part (ii) in the waveforms with the corresponding values for current and voltage. A ww ic 20 kΩ B + + 12 V Vc. R, •10 kΩ 0.05 μF
For the following pairs of voltage and current, indicate their phase relationship. Analyze whether the element involved in each pair is a resistor, inductor, or capacitor. Also obtain the value of R, L, and C if sufficient data are given.
transient response for this equation
I need the answer as soon as possible
Suppose that an inductor (L) - resistor (R) – capacitor (C) circuit is connected to an AC source that has a frequency of n rad/s. An engineer measured the values: the resistor's resistance which was found to be 10 ohms, the inductor's inductance was found to be 10 H, while the capacitor's capacitance was found to be 10 F. Determine the value of impedance. а. 10 ohms b. 33 ohms с. 11.5 ohms d. 1,080 ohms
Which of the following is true regarding the behavior of capacitors when energized by a DC source? a. At transient state, the capacitor behaves as an open circuit. b. At transient state, the capacitor behaves as a short circuit. c. At steady-state, the capacitor behaves as a short circuit. d. At steady-state, the capacitor behaves as an open circuit.
Q.15: The switch has been in position "a" for a long time. At t=0 the switch is moved to position "b". Use classical method to find the voltage across and current through the capacitor as a function of time? (Ans.: Vc(t)=80[1.25-e 20 b1002 10m H t%3D0S 30V 42 100V 2uF 5000t -5000t (cos5000t+sin5000t)] V & ic(t)=1.6e sin5000t A)
ABUSAL For the circuit shown in the following figure, if L= 28 H, V03D13 V, and R= 28 Q, answer the following 2 questions: Tin i(t) Vou(1) L. At what time the inductor is 25% charged from its steady state charging energy. Oa. 0.555 s Ob. 0.866 s Oc. 0.693 s Od. 1.083 s At what time the maximum power is delivered to the inductor.
Consider an inductor that is connected to a voltage source that has the waveform given in (a), and the current, power, and the energy of the inductor has the waveforms given in (b), (c), and (d), respectively. According to these waveforms, estimate the inductance of the inductor
Compute for the theoretical voltages across the resistor and inductor for 10kHz and 60kHz. Show the step-by-step computation. Express the voltages in polar form.