4.) Four people are attempting to move a stage platform across the floor. If they exert the horizontal forces shown, determine: a) the equivalent force-couple system at O [Answer: R = 222 i + 97.5 j lb, Mo = 102 lb in] b) the points on the x- and y-axes through which the line of action of the single resultant force R passes. [Answer: x= 1.05 in, y = -.462 in] c) the point along the axis AB through which the line of action of R passes. [Answer: x= 151.3 in] 87 lb 89 lb 66" 10 I | A 91" B 50 lb 66 lb 46°

4.) Four people are attempting to move a stage platform across the floor. If they exert the horizontal forces shown, determine: a) the equivalent force-couple system at O [Answer: R = 222 i + 97.5 j lb, Mo = 102 lb in] b) the points on the x- and y-axes through which the line of action of the single resultant force R passes. [Answer: x= 1.05 in, y = -.462 in] c) the point along the axis AB through which the line of action of R passes. [Answer: x= 151.3 in] 87 lb 89 lb 66" 10 I | A 91" B 50 lb 66 lb 46°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2) The box beam is constructed from four boards that are fastened together using nails spaced along the beam every 2 inches. The beam is subjected to a maximum internal shear force of 475 lb. a) Locate the neutral axis and compute the moment of inertia for the cross-section in in*. [Ans. to check: 1 = 197.7 in¹] b) Calculate the first moment of area in in³ at each of the two connection interfaces (i.e. once for the top flange and once for the bottom board). Draw a clear sketch of the cross-section showing the neutral axis and the necessary dimensions to calculate the first moment of area. [Ans. to Check: Qtop = 31.2 in³] c) Compute the shear flow occurring between the wood and the nails at each of the two connection interfaces in lb/in. [Ans. to Check: qbottom = 49.0 lb/in] d) Design the section by choosing the required shear strength of the nails (in lb). Check both interfaces but choose only one assuming you would like to use the same nails for the entire beam. [Ans. to check: 75 lb…
An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
Two forces F1 and F2 act on the screw eye. If theirlines of action are at an angle θ apart and the magnitude ofeach force is F1 = F2 = F, determine the magnitude of theresultant force FR and the angle between FR and F1.
a) M = 452 Ib-ft b) M = 575 Ib-ft c) M = 426 Ib-ft d) M = 3633 lb-ft Find the moment of the force Q about point O. The magnitude of the force Q = 105 lb %3D A 5.5 f升 5 ft 6 ft Q 4.2 ft y 3.5 ft В
3.25 The resultant of the three forces is a force R that passes through point B. Determine R and F. 36 lb 5 A- 4 ft- 30.5 lb 3 ft
For questions 1 to 5, consider a bent rod fixed at the wall at A and is acted upon by a 20- N force (parallel to the z-axis) and a 50-N force (parallel to the y-axis) applied at points B and C, respectively. y Z A 3. Which of the following moments is zero? Moment of the 50-N force about y-axis. Moment of the 50-N force about x-axis. Moment of the 20-N force about y-axis. Moment of the 50-N force about z-axis. -4 m- C -2 m- 50 N 20 N. x B X equivalent force-couple set at A of the applied forces 20 and C is the resultant couple
The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. Knowing that the entire shaft is made of steel for which G = 77 Gpa, determine the angle of twist at end A. 44mm -0.6m 60mm C 2000Nm B 30mm 0.2m 0.4m 250Nm A
3. Determine the moment of the force F about point P. P A 360 mm 500 mm X x 2 m -3 m O 3 m 2 m 4. The magnitude of the force P is 250 N. Determine the moments of P about point O. A P 600 mm x 1 m Y F = {2i+ 4j6k) kN 3 m y
Problem 6 A force system is shown below. 50 N 90 N 40° 40 N-m 0.40 m 0.80 m 100 N a. Determine the magnitude of the resultant? b. Determine the angle that the resultant force makes with the x-axis? c. Determine the magnitude of the resultant moment acting at point O? :::::: W 090 0.30 m 0.50 m
F 50° 25° The force vector F shown above has a magnitude of 27 kip. Which of the following best represents the unit vector acting in the direction of F? a) uf = {0.583i - 0.272j + 0.766k} O b) uF = {0.601i + 0.541j + 0.588k} c) uf = {0.541i + 0.601j - 0.588k} d) uf = {0.583i + 0.272j + 0.766k}
Problem 7.5 For the cantilever beam shown, it is required to determine the point where two bars theoretically can be cut off from the standpoint of the calculated moment strength, OM, of the beam. f, = 420 MPa and f.'= 21 MPa. 420 3@80 = 240 90 mm 90 mm 75 mm 10mmø stirups 4-28mm¢ W. 3.6 m 800 mm 725 mm 12. Calculate the moment the moment strength, ØM, , of the section. [in kN-m] 13. Calculate the maximum factored uniform load, w, the beam could support. [in kN/m] 14. Determine the distance from the free end where two bars theoretically can be cut off. [in m] 15. Determine the distance from the free end where two bars actually can be cut off. [in m] 16. Calculate the required development length, f dr at the support, if 90 hooked bars are used. [in mm]
9