Answered: 4. For the circuit of Fig.P4, B = 150.…

4. For the circuit of Fig.P4, B = 150. Determine: (a) The operating point (Ico and VeEQ) (b) The saturation current (I c(sat). +15 V R1 Rc 1.5 k 22 k. BDc = 150 %3D R2 4.7 k. Rg 680 N Fig.P4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

applied electricity and electronics solve asap
Q4: Consider a Zener diode with a nominal voltage (10v @ 10mA) and a resistance of 50 ohm. Calculate the expected Zener voltage if the diode current is doubled?
Consider the following circuit with Vs(t) = 2.0 + 0.02 sin(2 pi t) V,R1 = R2 = 25ohms Idc = 1mA, Vdc = 5V. Assume Vy = 0.7V and VT = 25mV.a) Draw the equivalent circuit under DCb) Determine the DC voltage and current through the diode.c) Draw the equivalent circuit under acd) Determine the total current through the diode
1. Consider the circuit below +12V R1=12K R2 The light-dependent-resistor (LDR) R2 is 1MQ when it's covered and 5002 when exposed to light. Let's model the LED lamp chip as two diodes in series, each with a forward voltage of 5V, so that the total voltage across it, when on, is 10V Assume beta = 100, VBE,On=0.7 and VCe,SAT=0.6V a. Suppose R2 is exposed to light and we assume the BJT is F.A. and the LED's are ON. Verify if our assumptions are correct. If the verification fails, what is a more appropriate state for the BJT and the LEDS? b. Suppose R2 is covered. Determine and verify the state of the BJT and the diodes.
(c) Figure Q4(c) illustrates a full-wave bridge rectifier used in ac voltmeter circuit. i) Explain the operation of diode D1, D2, D3 and D4. ii) Calculate the value of resistance R., ac sensitivity and de sensitivity. D1 D2 V=20Vme Rs 03 In=1mA R=2502 D4 R=2502 Figure Q4(c) Full Wave Bridge Rectifier
clear and correct or dislike
Need Solution
Given circuit network below, Determine the range of values R_ that will maintain Zener diode on if Vi = 20V. Determine the range of values Vi that will maintain the Zener diode on if R = 1.2kQ + 220 N Vz = 10V Pzmax = 400mW RL V;
For the subsequent questions, please refer to the circuit below. Assume that the diode is ideal (e.g. the voltage across it is zero volts when it is ON) IK VINZI IN=IV (+) I Sv(t Jo Vo Suppose we assume the diode is ON, what is V. in volts? Suppose we assume the diode is ON, what is the resistor current I in mA? Suppose we assume the diode is ON, our assumption is correct because the condition ID>=0 will hold as lp will be (in mA)... Suppose we assume the diode is OFF, this is a wrong assumption because when we solve for Vp with the diode as an open-circuit, the condition VD<=0 will NOT hold as Vp will be (in volts)...
Q4. For the clipping circuit shown, find the output waveform for the input voltage of v = 10 sinoot. Consider the diode has the following characteristics (ra= 20 Q, Va = 0.7 V, r, =0). %3D Rs 2.2 kf? VREF 2V
a) To what value R must be adjusted in the following circuit to make IZ = 70 mA. Assume VZ =20 V at 65 mA and ZZ = 23 Ω. What is the Zener voltage at 70o C, if it has a positive TC of 0.08 %/oC.? b) Using a Complete diode model, find the diode current (ID), diode voltage (VD), and output voltage (Vo) for the diode circuit shown below. Given that: Vs = 20 V, RL=3 kΩ , Barrier Potential VF = 0.3 V , and r’d = 70 Ω. If the diode was reversed and IR = 200 µA, Determine the diode reverse voltage (VR)
A half-wave rectifier with a 270 2 load resistor operates from a 120 Vrms 60 Hz household supply current through a 3-to-1 step-down transformer. It uses a silicon diode that can be modelled as having a constant Vf = 0.84 V drop for any current. vs(t) VL (t) RL (a) What is the peak voltage, vs,peak, of the secondary? What is the peak voltage, UL,peak of the rectified output? (b) For what fraction of the cycle (in percentage) does the diode conduct? (c) What is the average output voltage, V₁? (state which formula you used: the more accurate formula obtained via integration or the approximate formula) 1 (d) What is the average output current, IL? (e) You want to create a DC source with a peak-to-peak ripple voltage, Vr, of 11% of the peak output. (1) What size of capacitor should you add across the output? (2) What is the average voltage now? (State whether you used the more accurate or the approximate formula.)