4. Find Vout 120 kn 10 kn 10 kn 250 mV ww 2 kn 5 ka 350 mV ow o Vout 2 kn

Q: a. Describe the action of the circuit shown in the figure-1 below SPEAKER Vin RE

A: According to the question, we need to describe the working of the circuit shown below

Q: Describe the key principles of power system protection and the devices used to achieve it.

A: Power system protection is a critical aspect of electrical engineering that aims to safeguard power…

Q: A typical PV grounding system consists of the conductors and necessary to ground all metal…

A: The grounding is one of the safety measure that has to carried out to prevent human from live wire.…

Q: Current in a wire with open ends. Which of the following types of current can flow through a…

A: The following question is based on the condition of current flow.

Q: The characteristics of the Smith chart are summarized as follows

A: Characteristics of the Smith chart are summarized as follows:  The Smith Chart is used to display…

Q: In detail explain passive and active fire protection.

A:

Q: c. Design a circuit diagram with the following specifications: 110 volts battery, 10 Q, 15 Q and 30…

A: To solve above problem, one should know how to find equivalent resistance for series and parallel…

Q: What is metastability? How to avoid this.

A: Flip flop is a latch with additional control input (clock or enable ). A flip flop is used to store…

Q: Which of the following statements is correct regarding the efficacy and use of incandescent lamps…

A: In the given question, we need to find out the correct statement from the given option.

Q: Q2: Does ‘a three digit color coding of resistor values’ limit producible resistor value ranges?…

A: Yes color coding of resistor values limit the resistor value range. In color coding of three digit…

Q: Has anyone taken and or has any pointers on taking the industrial electricity NOCTI # 2050.

A: As per the NOCTI Job ready credential blueprint version:01, following points can be followed.…

Q: Q4\ Design a multi range D.C. ammeter by using indirect method to give the following ranges IA, 5A,…

A: Design a multi range DC ammeter.  For range of 1A, 5A, 25A, 50A and 100A. If PMMC meter have…

Q: What are the alternative ways that is affordable instead using a NUCLEAR POWER PLANT. explain it.…

A: Nuclear power plant :- It uses heat and source of heat is nuclear reactor. Heat is used for…

Q: What is voltage reference?

A: A voltage reference is an electronic device designed to maintain an accurate, low noise. It ideally…

Q: Short Problem: Given a series circuit comprised of the following element: 63.88-ohm resistor.…

A: In this question,  Find the angle of the impedance?  If RLC are connected in series.

Q: please show me the exact solution , thank you

A:

Q: Hello Sir. Good Evening. I have a question in my home work related Electricity Lesson. The…

A: Given, current flowing from wire, I=15 Ampheres Voltage applied,V=220 Volts diameter of wire, d=5mm,…

Q: 1. What is the goal of circuit theory? 2. Why would we want to use circuit theory and when can we…

A: Circuit: The electrical circuit is made up of a resistor, inductor, capacitor, voltage source,…

Q: a) PMMC meter has (10MA) half scale current deflection and (1500) internal resistance. Use this…

A: PMMC stands for permanent magnet moving coil. It works only for Dc because PMMC measures average…

Q: please show up the solution, thank you

A: The above question is based on the time constant of an RL circuit.

Q: How to turn-off a voltage source? A) Set it to zero. B Replace it with a short-circuit. C) You can't…

A: This is a basic problem of circuit. The solution is given in the next step.

Q: Write the names and functions of the three devices used for circuit laboratory experiments and…

A: In this answer we will discuss about any three devices that are used in the laboratory for…

Q: Which of the following are a pair of equal and oppositely charged particles? A) protons and neutrons…

A:

Q: Discuss five (5) good practices in electrical circuiting.

A: Always use gloves while working with electrical equipment and gloves must be insulated. While…

Q: Short Problem: Given a series circuit comprised of the following element: 61.19-ohm resistor.…

A:

Q: Part1: Resistors connected in series to each other The circuit shown below was generated on MapleSIM…

A:

Q: Just list, without detailed description. Give at least 5 examples of energy storage systems.

A:

Q: What does the circuit work like?

A: The above question is based on the firing circuit of a TRAIC.

Q: Short Problem: Given a series circuit comprised of the following element: 62.2-ohm resistor,…

A: In this question,  Find the angle of the impedance Z if RLC are connected in the series.

Q: , explain the FET types , working principles, structure and applications.

A: There are three terminals present in FET such as drain, source, and gate. FET stands for the…

Q: A copper wire with length of 500m has a diameter of 3mm. Its initial temperature is 20deg C. Find…

A:

Q: Sketch a diagram showing the ohmmeter face for a reading of 1.2 kQ. Indicate the setting of the…

A: Ohmmeter reading = 1.2 k-ohm Ohmmeter :- The ohmmeter is an electronic device that is used to…

Q: More five examples regarding this KCL method(with circuit figures and complete solution)

A:

Q: How to connect devices like IC, resistor and capcitor please explain in words and circuit?

A: A breadboard is used to make the circuit as per the requirement without any soldering. The…

Q: hat is “Voltage collapse”? Why does voltage instability occur? What are the countermeasures to deal…

A: Voltage collapse is the process in which the voltage at significant part of the power system becomes…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.