4. Explain the changes you would make to the circuit in Figure 19-4 in order to add a pushbutton that resets the counter into state 2.

Q: The latching current rating of thyristor is 50 mA. Minimum width of gate pulse to turn on the SCR is

A: Given data:Required information:

Q: The logical 1 input to an AND gate 74LS08 is a 1 Volt signal a 5 Volt signal a 15 Volt signal none…

A: In this question we will write that logical 1 input to an AND gate 74LS08 is how much volt...

Q: When D = 0 in the D-flipflop shown in figure, the output changes to, %3D D Q CLK - Q = 1, Q' = 0 ,…

A: D Flip flop D=0

Q: The energy gap which is present between the valence band and conduction band by separating these two…

A: Energy gap

Q: 1. Design a clamper to perform the function indicated. Determine the proper value of Voc Calculate…

A: From the input waveform given, the value of input voltage is  Vin = 10V

Q: Which of the following is on the discharge path of the circuit element C1 capacitor?

A: Output Buffer is on the discharge path of the circuit element C1 capacitor

Q: QUESTION 5 Determine the gate output for the input waveforms in Figure3 and draw the timing diagram.…

A: Given waveform with the logic circuit,

Q: 2. Describe the action of the circuit shown in figure-2 below a. Vin RE -O+Vcc SPEAKER

A: The given circuit diagram is shown below. We need to discuss the action of this circuit.

Q: Q5 Find the average output voltage of the full wave rectifier if the input signal = 24 sinwt and…

A: Types of converter DC-DC Converter (Chopper) DC-AC converter (Inverter) AC -DC Converter…

Q: In a half wave controller rectifier with R load and firing angle is Tt, the average output voltage…

A:

Q: 4. Sketch the output Vout for the given input Vin (shown on the right hand side) for each of the…

A:

Q: is the process of increasing the power, voltage or current by electronic means. O Switching…

A:

Q: Plot the output voltage waveform for the analog switch. Analog inpur Control voltage (high level…

A: Given, we are required to plot the output voltage when input signal is as,

Q: An SCR having a turn ON time of 5 use, latching current of 50 mA and holding current of 40 mA is…

A:

Q: What is soft switching designed to avoid? A. Rising edge resonance B. Switching losses C. Zero…

A:

Q: It has the highest power gain but the most unstable.Please point out the answer below. 1. Fixed-Bias…

A:

Q: Controller Load

A: Given Data:A step up chopper with,Output voltage Input voltage To Find:The duty cycle .

Q: An analogue indicating instrument with a scale range of 0-5A shows a current of 2.4A. A current has…

A:

Q: Which of the following statements about resistive transducer instrumentation is true? Strain gauges…

A: A resistive transducer instrument is used to measure the load, pressure or displacement.

Q: a) draw the block diagram of the statcom b) give the operating mode of the statcom c) draw the…

A: STATCOM : Static Synchronous Compensator The operating features of STATCOM are similar to a rotating…

Q: * Which circuit is changing the shape of the input Clamper circuit O Clipper circuit O None O

A: This is the problem of application of diode. The solution is given in the next step.

Q: like that of the clipper, the shape of the input signals of a clamper is changed. От O F

A: Clipper  :- A clipper circuit can remove certain portions of an arbitrary waveform near the positive…

Q: 2-adjust the A.C. oscillator to 8 Vp-p & 140Hz,R1=1K,L=400mH, R2-100 ohm

A:

Q: Bridge and center-tap is the basic .types of rectifier Half-Wave rectifier O Clipper O Full-Wave…

A: The explanation is as follows.

Q: An inverting Schmitt trigger has ±7 V supply voltages and values of Rf1 = 2.4kΩ and Rf2 = 1.3kΩ. The…

A: Given data: Supply voltage,Vin=±7 V. The voltage divider resistance of inverting Schmitt trigger,…

Q: A rectifier is a component that converts ac to dc by allowing the current to be

A: Given, Rectifier . Let's write the definition of rectifier.

Q: For the half-wave controlled rectifier shown, the thyristor is fired at an angle of 35° (firing…

A:

Q: In an On Off AC voltage controller, one of the given statement is false The duty cycle is always…

A: For the ON off ac voltage regulator  Which Statment is wrong

Q: 1. Determine the minimum and maximum output voltages for the voltage regulation in Figure below.…

A: Given R1=220 ΩR2=5 kΩ

Q: The type of triggering where the SCR can be turned on at a lower breakdown voltage Forward voltage…

A: Given  SCR triggering at low voltage breakdown

Q: Industrial Electronics There are 2 methods of turning off an SCR, identify 1 method and explain…

A:

Q: How do you clear a new EPROM?

A: We need to tell about how do we clear a new EPROM.

Q: 4. Load regulation is determined by a. changes in load current and the input voltage b changes in…

A: To do: 4. we have to select right option with respect to Load regulation. 5. we have to select right…

Q: The primary and secondary voltage drops respectively are: 96.2 volts and 9.62 volts O 0.962 volt and…

A: In this question we need to find a   primary and secondary voltage drop of the given signal phase…

Q: output waveform of a rectifier is called a/an

A: We need to tell about output of rectifier

Q: waht would the approximate amperage setting be if a welder were set to the high range (150 to 300)…

A: Given data, Range of amperage 150 amps to 350 amps  And knob adjusting at 5 0n 10 points scale…

Q: Routh Hurwitzof closed loop system with variable gain.

A:

Q: The logical 1 input to an AND gate 74LS08 is a 1 Volt signal a 5 Volt signal a 15 Volt signal

A: 1)74LS08 is a high speed AND gate IC.. 2) The input voltage for a logic HIGH is around 5 volt DC…

Q: The anode is connected to positive terminal with respect to the cathode & the gate circuit open, the…

A: Choose the correct option If the anode is connected to the positive terminal with respect to the…

Q: Explain why a serial adder is a sequential circuit.

A: Sequential circuits are circuits that contain memory elements such that their output is dependent on…

Q: At the following circuit, the latching current of the thyristor is assumed 40mA and the thyristor is…

A:

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.