4. Determine the resultant of the three forces acting on the dam shown and locate itsintersection with the base AB.W= 24,000 ibF = 6000 lb10,000 lb18'5. The Howe truss is loaded as shown. The wind loads are perpendicular to the inclined members.Determine the magnitude and position of the resultant force and its intersection with AB.1120 Ib2240 lb1120 lb101010'10103000 Ib2000 Ib1000 Ib

Answered: Image /qna-images/answer/fb99fd2a-728f-425c-86bb-e26c8a5fccbf.jpg

Answered: 4. Determine the resultant of the three…

4. Determine the resultant of the three forces acting on the dam shown and locate its intersection with the base AB. W= 24,000 ib F = 6000 lb 10,000 lb B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. If blocks A and B of mass 10 kg and 6 kg, respectively, are placed on the inclined plane and…

Q: A block is resting on a 30° inclined plane with a µ = 0.3. Find the required force P acting…

A: A force normally known as a push or pull. It is an interaction that can change the motion of an…

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

A: Deformation δ=PLAEWhere,P=ForceL=LengthA=Cross sectional areaE=Modulus of elasticityUsing…

Q: Homework 1 3 k Determine the reactions at the supports. EI is constant. Fixed A 10 ft Cy = 1.875 k…

A: Given data UDL Span length Point load Constant EI

Q: Consider the given beam below. Determine the following: a. Vertical reaction at the hinge support…

Q: A rectangular gate having width of 5 ft is located in the sloping side of a tank as shown. The gate…

Q: Isosceles triangular gate AB, as shown in the figure, is hinged at A. The horizontal force ( P) is…

A: Given Data: Specific gravity of oil is So=0.82. Density of the oil is given by: ρo=1000…

Q: The structure is loaded as shown in the figure. Determine the internal axial force, shear force and…

Q: A 40-mm diameter by 3.5-m long steel rod (1) is stress free after being attached to rigid supports…

Q: lem 2: 25 kips Determine the following: a. The reaction at support A, R = b. The reaction at support…

Q: 2. If the 200-lb block is released from rest when the spring is un-stretched, determine how far the…

A: Given :

Q: Solve for: 1. Maximum W in kN if each leg resist 10.098 kN. 2. If W is 49 kN. what is the force…

A: ##Solution of given problem part1, 2, 3 of mechanics ###3d vector forces##

Q: Problems for OUTPUT : I Compute the X and y components of oach of the forces shown T= 722 b Pe 200…

A: tan θ1=32θ1=tan-132θ1=56.31°tanθ2=12θ2=tan-112θ2=26.56°

Q: 30 kN 30 kN 30 kN 20 kN- 4 m -2m-2m2 m+2m- EA = constant E= 200 GPa A= 5000 mm Determine the total…

A: We have to determine the value of total displacement of joint E as per the given data in the…

Q: termine the reactions at support and thne forces acting on each member. By applying 1 uni oad…

A: In addition to its initial horizontal speed, a projectile's horizontal displacement depends on its…

Q: A cantilever beam supports the variable load shown. Calculate the supporting force RA and moment MA…

Q: Determine the values of a and 0 so that the forces shown will be in equilibrium. A=30 kN, B=40 kN,…

Q: 4 kN Determine the components of reaction at the fixed support A in Figure. Neglect the thickness of…

Q: determine the internal force in spring 1.

Q: Determine the location of the resultant from A of the coplanar parallel system shown in the figure.

Q: The sphere at A is given a downward velocity vo of magnitude 6 m/s and swings in a vertical plane at…

Q: 1.2.8

Q: The cylinder is subjected to a load that has a weight W. If the coefficients of rolling resistance…

A: The free body diagram of top surface is shown below.

Q: Analyze the frame shown below 37.5 kN/m BA C 4 m 4 m 3 m El = constant

Q: What is the equations for static equilibrium? * ΣFx 0 ΣFy -0 ΣFz 0 EMz = 0

A: Equations of static equilibrium - These are the equations developed, considering all the forces and…

Q: 1. The Dam ABC has a width of 30 m into the paper and the dam bottom length is 60m. The dam material…

A: We will calculate each moment and find FOS.

Q: ). Determine the resultant of the forces for the shown forces system" 720 N 48° 630 N 420 N

A: Given data Horizontal force Vertical force Inclined force Angle

Q: 880 F = 10 Q =( .kN F3 = 720 45 kN Oz = (. 50 On =( . 75 Calculate the forces F2 and F4 since the…

A: Forces in Equilibrium: When a system of force acts on an object and does not cause any net force on…

Q: * Determine the resultant of the coplanar force system 300 0 A 50 100 250 === 0 0=1.198.... R-50.15…

Q: Calculate (a) the elongation of the copper wire when the 50 KN vertical force is applied at and (b)…

A: Given data A copper with A= 500 mm2 L=1.30m E=120GPA P= 50 KN

Q: The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to…

Q: 2. Determine the reaction at point A and point B. 150 lb/ft A -6 ft 200 lb/ft 500 lb -3 ft -3 ft- B

Q: 3. A bar AB is supported by fixed supports at its ends as shown in the figure. An axial load of 12…

A: Please find attached images for solution.

Q: 1. If the 3 forces are in equilibrium, what is the horizontal component of the force P? (N) 2. If…

A: Given Data:

Q: A determinate frame carries a concentrated and distributed load as shown in the figure. Determine…

A: Step 1

Q: The cross-sectional area of each clamp forming a fixed-supported cage system from points C and D…

Q: Determine the components of the resultant force and the magnitude of the resultant. x = 20 m, y =15…

A: To find component of resultant force and it's magnitude

Q: Which is the correct equilibrium equation of the system along the x direction? 3 m X 2 m D B C 2 m 1…

Question

4. Determine the resultant of the three forces acting on the dam shown and locate its
intersection with the base AB.
W= 24,000 ib
F = 6000 lb
10,000 lb
18'
5. The Howe truss is loaded as shown. The wind loads are perpendicular to the inclined members.
Determine the magnitude and position of the resultant force and its intersection with AB.
1120 Ib
2240 lb
1120 lb
10
10
10'
10
10
3000 Ib
2000 Ib
1000 Ib

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please solve for RA within 20-30minutes. Have less time
Hydrostatic forces on inclined plane surface 6Q. A rectangular gate having a width of 4 ft is located in the sloping side of a tank as shown in the figure. The gate is hinged along its top edge and is held in position by the force P. Neglect the friction at the hinge and weight of the gate. Determine the required value of P. V Water Hinge Gate 60° 6 ft 10 ft
Show complete solution and Free Body Diagrams.
SHOW COMPLETE SOLUTION ANSWER ONLY NUMBER 22 , 23 AND 24 VALUES: A = 5 B = 5 C= 1 Y =25
Find the minimum value of P which will make it: a.) Slipb.) Tip Over
Using the Clayperon Method, Determine: 1. Support Reaction 2. Internal forces (Shear Force, Normal Force and Bending Moment) 3. Draw the Internal force diagrams P1= 3.246 kN P2- 4.846 kN q- 1.846 kN/n s2 1,946 3,246 3,946 3,946 3,946 3,94268 L
Given w=823 kN/m, find: (1) reaction forces at support A and B. (2) the internal forces 4m to the right of pin support A. Important Note: You have to clearly show the complete solution including FBD and Equations of Equilibrium.
Pls answer asap
A simply supported beam of length 7 m has a concentrated couple M of 10 kN-m applied at the right end. Determine the location of the maximum deflection from the applied load. O 2.75 m O 2.96 m O 2.50 m O 2.252 m Calculate the value of the maximum deflection. Use E = 200, 000 N/mm^2 and I = 60x10^6 mm^4. O2.62 mm O 131 mm 10.52 mm 5.26 mm
Use E= 200 GPa, I = 800 x 105 mm² when necessary. For the beam loaded as shown, determine the reaction components using Conjugate Beam Method 3.00 3.00 300 kNm 6.00 90 kN/m 7.00 12.0 m 4.00 6.00 P = 229kN
WA 4-m bar of negligible weight rests in a horizontal position on the smooth planes shown in the Figure, if T = 30 KN and x = 1 m. Determine the Reaction at A. 1m P = 20 kN 30° 45° 4 m 16.82 KN None of the above O 44.83 KN O 25.89 KN 36.60 KN
A wooden beam 150 mm wide by 300 mm deep is loaded as shown. fb = 8 MPa a) Determine the maximum capacity of the beam. b) Determine the value of maximum value of P if x is 2m.