4. Calculate the power required to compress 18 kg/min of NH, from saturated vapour at 1.4 bar to condensing pressure of 10 bar by a two stage compression with flash intercooling by liquid refrigerant at 4 bar. Assume the refrigerant leaves evaporator as saturated vapour and leaves condenser as saturated liquid. Also find out the load in evaporator in tonnes of refrigeration. Calculate the power required without multi-staging.

Q: Show your complete solution including the diagrams and box your final answers with their appropriate…

A:

Q: ab) What is the composite area's moment of inertia based on axis Yo?

A: we have to determine the MOI

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat…

A:

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: Part C - Radius of curvature for AB and BC Determine the radius of curvature for AB, PAB, and for…

A:

Q: 2. Write 5 details found on the drawing title block?

A: The bottom right hand corner block in engineering drawing sheet is known as title block. This block…

Q: In a workshop, Drilling operator is working on a Drilling machine. The drilling operator needs to…

A:

Q: 8. A note in the comment section of a title block mentions that all faces should have a +.10…

A: Circularity (roundness) tolerance is 2-D in nature.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: 3. What makes EDM become a key in tool and die making machine tool ?

A: The main reason of using EDM in die making process are:-

Q: can you please write it in a proper way?

A:

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: short notes on any two types of chips formed during metal cutting operation

A: Metal cutting is defined as "the act of eliminating undesirable material from a block of metal in…

Q: A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How…

A: Given12 guage sheet metal sheet thickness t=7/64 inchthickness of stacked sheets t2=171 2inches

Q: Write the types of keys and sketch freehand of them with dimensions and equations.

A: A key is a machine element that is fitted in the axial direction with the mating parts in pulleys…

Q: PART VI. Given that f(x,y) = (x +y)/2k, where x=-1,1,2 and y= 0,2,4 1. Find k 2. Find the marginal…

A:

Q: Q34 gine exCumphe far nolineer operautor an

A: Given: To give an example of non-linear operator.

Q: 1. How is fraction changed to decimal? A. Divide the denominator by the numerator B. Divide the…

A: Since we answer only one question at a time, we will answer the first one. Please resubmit the…

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: That is the answer I have and it is marked as wrong, could you please do it again and see if you get…

A:

Q: I need problems 7, 8, and 9 answered pertaining to the print attached below.

A: Cutting plane line:Cutting plane lines are represented by dotted chain line as shown in the figure.…

Q: I need help answering this Review Activity

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Please show all the steps, thanks

A:

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Q: friction t

A: FIg:FBD Fr=μN∑Fy=0N=mgcosθ∑Fx=0μN=mgsinθμmgcosθ=mgsinθμ=tanθ

Q: You've been asked to design a stamping tool as shown. What are the internal forces at A and B? Ans:…

A: Draw FBD of the given system

Q: Give 1 example of methods of section

A:

Q: 10) Define the slip angle.

A: The angle between the direction of the wheel in which it is pointing and the direction in which it…

Q: Required handwritten answer, Please be sure . Don't provide wrong answer. 1)An engine produces 238…

A:

Q: Differentiate 1. Method of removal 2. Kind of work material 3. Type of cut EDM, USM, and ECM as to

A: Wire EDM  is an electro thermal manufacturing technique in which a thin single strand metal wire…

Q: Write the Column Formulas?

A: Types Critical load Both ends hinged π2EIl2 one end hinged other end fixed 2π2EIl2 both ends…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.