4. Biot hypothesized that the shear modulus is influenced by the presence of the pore fluid. 5. Pure shear failure depends on the intermediate principle stress. 6. Tensile failure usually occurs when the greatest effective principal stress surpasses the formation rock tensile strength.

Q: please answer the table

A:

Q: Heat is negative when energy is transferred to a system from its environment

A: Correct option is:

Q: Work of a spring force (with final position in compressed state, initial position in undeformed…

A:

Q: 1: The crane shown is symmetrically supported by two outriggers at A and two at B. If the crane and…

A: Given, Downward mass at G1 , m1 = 18000 kg Downward mass at G2 , m2 = 1800 kg Downward mass m3 =…

Q: fx A C 1 1 3 13 4 The image above shows a section of a Google sheet. What formula should be written…

A: Answer: The correct answer is option (a)  =sum(A1:A3).

Q: QUESTIONS 1. What is the critical issue? What can be done about it? 2. Can excellence in project…

A: Any topic subject to the decision-making authority of any Committee that might have a major…

Q: 4. A flywheel has angular acceleration a₂(t) = 8.60 ™ - (2.30a) t, where counterclockwise rad s²…

A:

Q: An adiabatic process is one during which no energy enters or leaves the system by heat

A:

Q: Write the mathematical form of Newton's second law of motion.

A: Newton’s second law of motion states that the resultant of actual force is always equal to effect or…

Q: Write F if True and T if False. Golf countries are rich because of their oil deposits

A: It is true(F) that gulf countries are rich because of their oil deposits.

Q: 5. The damping ratio in terms of the damping constant e and critical damping constant c is given by…

A: Damping ratio is defined as the ratio of the damping constant and ctmrtical damping coefficient.

Q: A central heating system from a house consists of 50m of 15mm outside diameter copper pipe with a…

A:

Q: Question 2) A 0.2-kg mass moves along the x-axis. The resultant of all the forces acting on the mass…

A:

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: Q.1) Three forces and a couple moment are applied to an angle bracket as shown. The 50 lb force acts…

A: (a) Consider the diagram and draw a single resultant force and couple moment at point B.

Q: 10. Atmospheric pressure, Stau 11. Atmospheric pressure, stated in psig, is 12. Atmospheric…

A: 10. 14.7 psi 11. 0 psi (14.7-14.7) 12. 29.9212 in Hg 13. above and below 14. inversely as long as…

Q: Determine the internal forces acting in members, HC, JD, and KE. State if the members are in tension…

A: Drawing the free body diagram of the system as shown below,…

Q: X-ray Diffraction 9. The metal iridium has an FCC crystal structure. If the angle of diffraction for…

A: The given information in the problem is shown in the following attached image:

Q: Find the mass moment of inertia, Izz, for the spherical ceramic femoral head ball (with a…

A: The radius of the sphere is r, The radius of the cylinder is r/2. The height of the cylinder is…

Q: 3. Find the moment of inertia of a hoop (a thin-walled, hollow ring) with mass M and radius R about…

A:

Q: A triangular brass casting is shown. The block weighs 15.30 pounds. Brass weighs 526.7 pounds per…

A:

Q: 6. Tensile failure usually occurs when the greatest effective principal stress surpasses the…

A: Explaining  tensile failure and failure plane and loading and unloading path of perfect elastic…

Q: A solar water heater mounted on the roof consists of two flat plates. Water enters at A and exits at…

A:

Q: Mechanics is the study of bodies under the action of forces. It is the foundation of many…

A:

Q: The Carnot cycle consists of two adiabatic processes and two isothermal processes

A: This question is from thermodynamics.

Q: The basketball player likes to release his foul shots with an initial speed vo = 26.2 ft/sec. What 2…

A:

Q: A puck of mass m, - 74.0 g and radius r,- 4.10 cm glides across an air table at a speed of v- 1.50…

A:

Q: Car A rounds a curve of 175-m radius at a constant speed of 36 km/h. At the instant represented, car…

A:

Q: The official record for the largest diameter loop-the-loop in a car is currently 19.49 m (see Figure…

A:

Q: factor of safety

A: True

Q: (a) 4 KN Ax 2m 50 Ay (b) 17 Ax 5ft 80 1b (c) ト

A:

Q: 9. The orientation of the failure plane is independent of the confining stress 10.The modified…

A: In a frictional process, the failure occurs due to the shear.

Q: A 77 1/2-4 + D ·(a) This beam will not have an internal bending moment question to the correct…

A:

Q: 5. The temperature distribution along a fin with insulated tip is given by: mx e

A: Temperature distribution along fin with insulated tip to be find out

Q: 5. Coefficient of performance of a reversible heat pump is always higher than that of an…

A: The coefficient of performance (COP) of a heat pump comprised of reversible processes (CARNOT) is…

Q: Three crates are kept in static equilibrium by the frictionless rope-pulley-spring arrangements…

A: Free body diagram:

Q: 2-25. As the balloon ascends, measurements indicate that the temperature begins to decrease at a…

A:

Q: 1. Heat flow= thermal conductivity x (Area xTemperature ). 2. Change length AL = a ( LAT ). 3.…

A:

Q: The rate of discharge through the nozzle DECREASES when the exit pressure is gradually reduced.

A:

Q: he second law of thermodynamics state that a machine that operates in a cycle, taking in energy by…

A: The given statement is true.

Q: In any process where heat is added to the system and work is done by the system,the net energy…

A: This question is from thermodynamics fist law.

Q: In Diesel Cycle air is compressed above autoignition temperature For Otto cycle Efficiency increases…

A: Part a- true or false) Diesel cycle I combustion cycle in which fuel is compressed enough to ignite…

Q: When we have an isothermal expansion, the expression of the entropy is written as: T. AS=-

A: Isothermal process: The process in which the temperature of the process is constant throughout the…

Q: Rod AD is supported by two cables as shown. The tension in cable AB is 500 N and in cable AC is…

A: