4. A reinforced concrete beam has a width of 400 mm and a total depth of 550 mm. The longitudinal bars at the top are 2-28 mm dia. and 4-32mm dia. at the bottom. Concrete strength is f'c= 22 MPa (p. = 1950 ) and steel yield strength fy= 420 MPa. Steel cover is 70 m3 mm. Find the moment capacity, the transformed moment of inertia, and the safest uniformly distributed load that the beam can carry if the length of the beam is 8 meters.

4. A reinforced concrete beam has a width of 400 mm and a total depth of 550 mm. The longitudinal bars at the top are 2-28 mm dia. and 4-32mm dia. at the bottom. Concrete strength is f'c= 22 MPa (p. = 1950 ) and steel yield strength fy= 420 MPa. Steel cover is 70 m3 mm. Find the moment capacity, the transformed moment of inertia, and the safest uniformly distributed load that the beam can carry if the length of the beam is 8 meters.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assume straight line instead of parabola for stress-strain curve of concrete as follows and partial factor of safety as 1.0. 0.002 0.67 0.0035 Strain A rectangular under-reinforced concrete section of 300mm width and 500mm effective depth is reinforced with 3 bars of grade Fe 415, each of 16m diameter. Concrete mix is M20. The depth of the neutral axis from the compression fibre is
INELASTIC BENDING OF SINGLY REINFORCED CONCRETE BEAM SECTION *A trapezoidal concrete beam is casted with a compressive strength of about 20 MPa. The beam is reinforced with 3- 32 mm diamater bars in the tension zone with a yield strength of 275 MPa. The bar is located 100 mm from the bottom. Determine the nominal bending strength. Assume that the beam is symmetrical about the vertical axis with a depth of 600 mm, a top width of 500 mm, and a bottom width of 200 mm.
Concrete beam.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 27 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only.
rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel area for a tension controlled singly reinforced condition in positive bending
Use f'c = 30 MPa and fy = 415 MPa. The unit weight of concrete is 24 kN/m³ . The floor of a cantilever floor system is made up of a 150mm thick concrete slab (cast monolithically with beam) and the beams have widths of 300 mm, a total depth of 560 mm, and are to be reinforced with 5-Ø28 mm bars. The center-to-center spacing of beams is 4 m. The cantilever floor system is also built using 4m cantilever reinforced beams as supports. a) Find the maximum service live load (kPa) that the current floor design can support. b) Suppose that the floor will need to carry a superimposed service dead load of 2 kPa and service live load of 7.2 kPa, will the existing floor design be adequate? If not, redesign the beams (find the appropriate number of Ø28-mm rebars and provide a final sketch). Use cc = 40 mm, stirrup diameter of 10 mm, and nominal maximum aggregate size of 20 mm.
Problem #1. The base of a rectangular reinforced concrete beam is 300mm and the effective depth is 550mm. Concrete compressive strength on the 28" day is 24MPA and steel yield strength is 415MP.. Determine : a. The depth of compression block (in mm, 2 decimal places), the strain in the tension steel (5 decimal places) and ultimate moment capacity (in KN.m, nearest tenth) of the beam if it is reinforced with 4-32mm diameter bars. b. The depth of compression block, the strain in the tension steel and ultimate moment capacity of the beam if it is reinforced with 4-20mm diameter bars.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the nominal moment capacity in kN∙m of the beam in negative bending.
A prestressec concrete beam 300 mm wide and 600 mm deep is prestressed using 5 high tension bors f 12 mm o provide at 220 mm from the soffit of the beam. The effective stress in the steel is 800 N/ m Find the bending that niust be applied to the section to just auoid tension at the soffit of the beam.
A circular Column has dia of D 30 in. Concrete Compressive strength at 28 days is of steel is (60 + 60) ksi. Determine the design capacity of circular column and 8 # 11 bars is used. (4 + 60) ksi and yielding strength
just answer d to f
The maximum compression in a concrete beam fiber is 6.2 MPa. The depth of the neutral axis is 124 mm and the characteristic compressive strength of the concrete is 25 N/mm?. Determine the effective curvature of the beam,