4. A railway embankment is 10m wide with side slopes 1.5 to 1. Assuming the ground to be level in a direction transverse to the center line, calculate the volume contained in a length of 120 meters by prismoidal formula. The center heights at 20m intervals being in meters 2.2, 3.4, 3.8, 4.0, 3.6, 2.8, and 2.5. (CO2, Cognitive, Apply)

4. A railway embankment is 10m wide with side slopes 1.5 to 1. Assuming the ground to be level in a direction transverse to the center line, calculate the volume contained in a length of 120 meters by prismoidal formula. The center heights at 20m intervals being in meters 2.2, 3.4, 3.8, 4.0, 3.6, 2.8, and 2.5. (CO2, Cognitive, Apply)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical gate with surface XY is supported by a hinge at point 1. The length of the gate perpendicular to the figure is m. Solve for the location of the horizontal component above point 1 in m. Unit wt of water = 9.81 kN/cu.m. LENGTH=6 RADIUS= 7 ANGLE = 65 RADIUS 1 2.55 2.11 2.63 2.13 ANGLE
Determine the Hydrostatic Force (in newton) from the fluid surface. Unit weight = 9809.4321 N/m³ and height H = 1.54321 m For equation of the eurve: whenx 1,y=1;whenx=2,y=16;whenx=3,y-81; when x 4,y-256- Hint to get this equation: "Finding the rute for nen linear sequence" use equation y = xª for the non-linear curve H
Please observe the directions... Don't copy from other websites solution
Please show complete detailed solution. P=53
For the system below, EI is constant. If x = 9.48 m from point A, determine the value of EI(Δ) ? If x = 2.80 m from point A, determine the value of EI(θ) ? If x = 8.32 m from point A, determine the value of EI(Δ) ? If x = 6.13 m from point A, determine the value of EI(θ) ?
A railway fill is 12 m wide. The ground is level in a direction transverse to the centerline. The sideslope is 1.5:1. The center heights at 20 m interval are 3.7 m, 2.6 m, 4.0 m, 3.4 m, 2.8 m, 3.0 m, and 2.2 m. Determine the volume between section 1 and 2, 2 and 3, 3 and 4, 5 and 6 and total
USING DOUBLE INTEGRATION METHOD Consider 250 mm x 250 mm (bxh) mm section and e = 100000 MPa DETERMINE VERTICAL REACTION AT B Values:A = 9.4 MB = 5.5 MC = 10.6 KN/MD = 33 KN
None
3. An opening gate was installed in an irrigated land drainage system automatic to avoid flooding, articulated in O and with an angle of 0 = 40° with the horizontal, as shown in the figure. The gate weighs W = 9.0 kN and has a height L = 1.7 m; width w = 1,8 m. a) If the height of water is equal to h = 0.65 m, determine the resulting force of water on the gate and the application point in relation to point O. b) To what height of water h will the gate open? That is, rotate in the anti-schedule. L h
An open rectangular tank measuring 6m long, 2.05 m wide, and 3 m high is filled to a depth of 1.9 m with gasoline (SG=0.68). The tank is attached to a truck that is traveling horizontally at 9.81. How much water (m³) is left if the track is traveling horizontally at 9.81 m/s^2
A trough is 12m long, 5m wide, and 3m deep. The vertical cross-section of the trough parallel to an end is shaped like an isoceles triangle (with height 3m, and base, on top, of length 5m). The trough is full of water (density 1000kg/m³ and g = 9.8m/s² is the acceleration due to gravity). a) Find the amount of work in joules required to empty the trough by pumping the water over the top. b) Find the amount of work in joules required to empty the trough by pumping the water out of a spout 4m high.