4. A pump is tested in the laboratory and the following data were obtained. Torque = T= 6.78 Nm Rotational speed = w = 20 Hz Inlet pressure = Pi = 68.95 kPa Outlet pressure = p2 = 193 kPa Velocity in the inlet line = V= 2.44 m/s Height to inlet gauge z1 = 0.61 m Height to outlet gauge = 22 = 1.52 m Inlet flow line = 2- nominal schedule 40

4. A pump is tested in the laboratory and the following data were obtained. Torque = T= 6.78 Nm Rotational speed = w = 20 Hz Inlet pressure = Pi = 68.95 kPa Outlet pressure = p2 = 193 kPa Velocity in the inlet line = V= 2.44 m/s Height to inlet gauge z1 = 0.61 m Height to outlet gauge = 22 = 1.52 m Inlet flow line = 2- nominal schedule 40

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. In the Figure below, determine: (a) the calibration range of the DP transmitter in inches of water, (b) the differential pressure head in inches water at the transmitter at 75% level Given: 100% S HLL NLL LLL Xx Y3=130 in. SG3=1.26 S = 60 in Y2 = 30 in. SG2=1.12 Y1 = 15 in. SG1 = 0.82
https://www.engineeringtoolbox.com/dynamic-viscosity-motor-oils-d_1759.html
2 Pressure gauge 4 F the hydraulic cycle in figure -consist of:6 5 ww M 3 Feed direction 8 filter O pressure gauge O relief valve O pump O
quick pls
Number 3 pls
Number 4 pls
METERS | FEET MODEL: IA6BJM SIZE: 8" x 6" x 13" RPM: 1750 76+250 PRESSURE MAX: 120 PSI GRAPHIC 61+200 FØ13," (75 HP) SCALE 70% 75% 80% 82% 60 GPM Ø12%" (60 HP) 83% 84% 83% 46-150 82% 80% Ø12%" (50 HP) 75% 011%" (40 HP) 70% 65% 31+100 100 BHP Ø10%" (30 HP) NPSHr ftm 75 BHP 60 BHP 30+9 15+50 50 BHP 30 BHP 40 BHP 20+6 NPSH. 10+3 GALLONS PER MINUTE LITERS PER MINUTE Refer to the system curve drawn on this pump curve. If the pump is to move 1200 gpm, what is the expected system total dynamic head (ft)? 1136+300 2271+600 00620 4543+120아 5678+1500- 6414+1800 7949+2100- 9085+2400 * 11356+3000 10 FEET
3. A seamless steel pipe carries 2000 m³ of steam per hour at a pressure of 1.2 N/mm². The velocity of flow is 28 m/s. Assuming the tensile stress as 40 MPa, find the inside diameter of the pipe and its wall thickness. [Ans. 160 mm; 5.4 mm] 4. Compute the dimensions of a flanged cast iron pipe 200 mm in diameter to carry a pressure of 0.7 N/mm².
During Extension of vertical cylinder Pressure Reading PSI 140 500 Flow Meter Reading GPM 2.8 0 Time to Extend 1.03 N/A At Extension (when cylinder is stopped) Calculate the maximum force that the vertical cylinder can generate during extension and retraction based on a system pressure of 500 psi.