-4. A lossless transmission line has a characteristic impedance of 100 N and is terminated in a load of 75 N. The line is 0.75 wavelength long. Determine: a. The sending-end impedance b. The reactance which, if connected across the sending end of the line, will make the input impedance a pure resistance

-4. A lossless transmission line has a characteristic impedance of 100 N and is terminated in a load of 75 N. The line is 0.75 wavelength long. Determine: a. The sending-end impedance b. The reactance which, if connected across the sending end of the line, will make the input impedance a pure resistance

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.15MCQ

See similar textbooks

Related questions

Q: In a solar dish, which device converts the thermal energy of fluid into mechanical energy? O a. gas…

A: In a solar dish, Which devise converts the thermal energy of fluid into mechanical energy.

Q: Assume that memory location $c100 holds a data byte =$37, [ACCA]= $B8 and [ACCB]=$FE. For each of…

A: Given data: $37 data at memory location $C100ACCA=$B8ACCB=$FE

Q: Which of the following is NOT required for Lasing action? Absorption Spontaneous emission…

A: Lasing action The abbreviation for light amplification by stimulated emission of radiation is laser,…

Q: what is the derating factor ,if any,for thirty five conductors in a 25 degree conduct nipple ? 1)…

A: The derating factor for conductors refers to the adjustment made to the allowable ampacity…

Q: A single pulse 1nsec long is sent through a 50 ohms transmission line with a load resistance of 75…

A: To calculate the time it takes for the return current to reach the return conductor we first need to…

Q: Q1. Rank the below events in ascending order of generated frequencies (from the slowest to the…

A: A power system's frequency is a dynamic variable that changes in real-time and represents the…

Q: 77. Which is proportional to the frequency in her a. the number of turns b. the type of material…

A: The rate at which operation reapeats for a particular period of time is known as frequency.

Question

Microwave

3-4. A lossless transmission line has a characteristic impedance of 100 N and is terminated
in a load of 75 N. The line is 0.75 wavelength long. Determine:
a. The sending-end impedance
b. The reactance which, if connected across the sending end of the line, will make the
input impedance a pure resistance

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please help with the solution.
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
A lossless transmission line has a capacitance per unit length of 90 uF/m (microFarad/meter) and an inductance per unit length of 1 nH/m. The load impedance ZI is purely resistive. Both the load impedance and the generator impedance are 50 ohms. Source voltage amplitude is unknown at this point. Find the characteristic impedance and the propagation velocity for this transmission line!
1. a. A purely reactive load impedance Z₁ =jX terminates a transmission line. Prove that the reflection coefficient magnitude |K| is always unity, assuming the characteristic impedance Zo is real. What is the VSWR of the line in this case? b. Consider the transmission line in the figure. i. Determine the SWR on transmission line ii. The input impedance If=102, find I, in the figure. WC 100/0*V] 20 922 Air, lossless Z-50 £2 2.72 40 2 ele 3002
A 105MHz, 90 v peak signal is incident on a 50-ohm transmission line. The line is 125m long and is terminated in 300-ohm load. What is the SWR for this situation? Find the reflection coefficient.
The capacitance per unit length and the characteristic impedance of a lossless transmission line are C and Zo respectively. The velocity of a travelling wave on the transmission line is (a) Z.C (c) Zo C - UN (b) Z.C (d) Z
Microwave
Please explain each answers... And choose the correct one
For a lossless trabsmisison line, the characteristic impedance is 80 ohm. If the capacitance per unit length is 1.5 mh/m then what will be the inductance per unit length.
c) For a transmission line w/characteristic impedance Z0 = 50 W. At some point of the line, a forward wave has the voltage V+ = 10V and backward wave has the voltage V- = 4V. i) Currents of the forward wave and backward wave at that point. ii) Measured voltage and current at that point. d) A transmission line has the following properties: Length, L = 3 m. Characteristic impedance Z0 = 50 W. The load impedance ZL = 100 W. And phase constant b = p/3. Assume the forward voltage at z = 0 is VA =10ejp/4 At z = 3m, calculate: i) Forward voltage and forward current. ii) Backward voltage and backward current. iii) Measured (total) voltage and current across the load
Find current
Write down the general expression for the input impedance of a transmission line of length 1 and characteristic impedance Zo terminated by a load impedance Z1 . A complex load admittance Y = (a -jb)/ Zo terminates a length of line quarter wavelength long. Show that an impedance of (jb Zo) will have to be connected in series with this line to create a purely real input impedance. What length L of short circuited line of characteristic impedance Zo and propagation constant B would this correspond to? A quarter wave section of transmission line, is now inserted between this line (which includes the added series impedance) and a voltage source of internal impedance Zo. Show that the new line should have a characteristic impedance of Zo va in order to produce a matched load.