4. A 45kg, uniform 0.6m x 0.4m rectangular block is initially resting on a horizontal surface. A horizontal 200 N force is applied to the left side of the block, 0.5m above the surface. What is the initial angular acceleration, a, of the block, when the force is applied? 0.4 m 200 N 0.5 m 45 kg 0.6 m Ms=0.8 Mk=0.7

4. A 45kg, uniform 0.6m x 0.4m rectangular block is initially resting on a horizontal surface. A horizontal 200 N force is applied to the left side of the block, 0.5m above the surface. What is the initial angular acceleration, a, of the block, when the force is applied? 0.4 m 200 N 0.5 m 45 kg 0.6 m Ms=0.8 Mk=0.7

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam and the loading as shown in figure below, determine (1) the slopes at 2 and 3, (2) the vertical deflection at the midpoint of the distributed load. 12 kN/m 1m E 200 GPa 2 1 m. I= 4 x 10 mm 3
PLEASE DO IT RIGHT THIS IS MY 3RD TIME!!!
A uniform concrete slab is supported by the two cables as shown. Compute the vertical displacement of the concrete slab. steel Area=300sq.mm L=5m 1m P=18N 4m W=25N Aluminum Area 500sq.mm L=3m
SOLVE THIS USING CBM. THANK YOU. The roof beam of a building is subjected to the loading shown. If a 3/8-in. deflection is permitted at the cantilever end before the ceiling & roofing materials would be damaged, determine the required moment of inertia for the beam. Use E = 29,000 ksi. 24 kips 0.72 kip/ft 0.48 kip/ft B
Determine the stress of the compression steel. 200 나 60 20mm 450 32mm 60 A 95.64 B 40.78 4.78 90.858 D.
4. A 25 mm diameter shaft is pulled through a cylindrical bearing as shown (not rotating). Oil is used as a lubricant and fills the 0.3 mm gap between the shaft and the bearing. The kinematic viscosity of the oil is 8.0 x 10-4 m²/s and the specific gravity is 0.91. Determine the force P required to pull the shaft at a velocity of 3 m/s. Assume the velocity distribution in the gap is linear (i.e. Couette flow). Draw the free body diagram and show the forces. Bearing Shaft 0.5 m- Lubricant
The cross section of a quarter circular concrete block JKL as shown in Figure 5 is located at thebottom of a reservoir. The width (perpendicular to the paper) is 3 m. The specific weight of theconcrete block is 24 kN/m3. The coefficient of friction between the base of the block and thefoundation is 0.43. Determine if the concrete block is stable or not against sliding and overturningif the water is:A. At side XB. At side Y, with the same water level as A.
SITUATION E:A 30 m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg supported for full length. The tape was used in measuring a line 938.55 m long on a smooth level ground under a steady pull of 10 kg. Assuming E= 2x106 kg/cm2 and the unit weight of steel to be 7.9x10-3 kg/cm³. Determine the total correction for increase in tension -0.068 m +0.068 m -0.038 m +0.038 m
2. Given the beam shown. If the modulus of elasticity is 200 GPa and the moment of inertia is 100,000,000 millimeters^4, determine: a. Deflection at the free end b. Slope at B c. Deflection at B 100 kN 50 kN 400 kN-m 6.0 m 4.0 m
Determine the location and magnitude of the maximum absolute deflection in AB between A and the center of the beam. (b) Assuming that beam AB is a W460 *113 rolled shape, M0 = 224 kN·m, and E = 200 GPa, determine the maximum allowable length L so that the maximum deflection does not exceed 1.2 mm.
A 2.8m square plate is completely immersed under water in a vertical position such that the two edges of the square are horizontal. It is immersed such that the center of pressure is located 8cm below its center of gravity. Determine the resultant hydrostatic force on one side of the plate. 634KN 706KN 666KN O 596KN