4. A 3-phase, wye-connected alternator is rated at 2000 kVA, 13.5 kV. The effective resistance and synchronous reactance of the armature are 1.3 ohm and 20 ohms, respectively. What is the regulation in percent for a power factor of 0.80 lagging? A. 8.74 C. 13.85 B. 15.52 D. 14.45

4. A 3-phase, wye-connected alternator is rated at 2000 kVA, 13.5 kV. The effective resistance and synchronous reactance of the armature are 1.3 ohm and 20 ohms, respectively. What is the regulation in percent for a power factor of 0.80 lagging? A. 8.74 C. 13.85 B. 15.52 D. 14.45

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In your own words(not googled) please answer and help me understand the following a. What is a LED? Explain the working of a LED and give at least two applications. b. Why do LEDs need series current-limiting resistors? c. How does LED differ from an ordinary diode? d. What is a photodiode? Explain how it works and give at least two applications. e. What is a/an: i. Tunnel diode ii. Optoisolator iii. Varactor diode iv. Shockley diode
A Zener diode with an arbitrary Zener voltage is used to build the circuit below. Calculate:(a) The current I_z(b) The voltage V_out(c) The power absorbed by the Zener diode ASSUME ARBITRARY VALUES FOR ALL OR PLUG IN VALUES U CAN USE AS AN EXAMPLE.
Solve for currents of two diodes (ID1 and ID2), voltages across two resistors (VR3 and VR2) and I (IR2 and IR3).
Using the constant-voltage model (all diode's turn- on voltage, V_D = 0.7V), plot the input vs. output characteristics (VTC, voltage transfer characteristic). On your plot, x-axis is V1 and y-axis is VO . In your plot, you have to mark the slope and the values on x-y axis in detail. D3 D4 KIKH o Vo 1ko 2kn
answer question 3.b quickly in 1 hours… thank you
Subject: Electronics Engineering To study V-I characteristics of the semiconductor diode and determine D.C & A.C resistance. Write in your own language what you learn from this experiment
Fill the blanks with suitable following terms (AND gate, Potential Transformers (PT), cathode ray oscilloscope CRO, electronic switch Current Transformers (CT), DC component, cathode ray tube (CRT), AC component, electron.gun. 1.The heart of a ............is the................. the electron beam is generated, accelerated, and deflected in accordance with the input signal. 2. Power measurements in high-voltage high current circuit can be effectively done by the use of...and.. ...in conjunction with conventional wattmeter. 3. The sig ...ose frequency is to be measured is converted into a train of pulses (Using Comparator for example), one pulse for each cycle of the signal and applied continuously to an...A 4. In Average Responding Voltmeter, the AC signal is first applied to the blocking capacitor used at the input to block any..................in the input voltage. 5. Dual Trace Oscilloscope This CRO has a single.....................whose electron beam is split into two by an…
For the diode circuit to the right 8002 a V' V 40mA (T 1002 0.001V' a) To the left of points a and b, find the load-line relation by expressing the current, I with voltage, V. HINT: Write KCL equation for the circuit diagram and write I in terms of V from that KCL equation. This will be your load-line equation.
Measuring the hall coefficient determines which of the following? a) temperature coefficient and thermal conductivity b) none of the above c) mobility of load carriers d) type of conductivity and concentration of charge carriers
Electronics Question:- What is difference between "==" and "===" in behaviour modellina of verilog
Problem4. Resistors are given a power rating. For example, resistors are available with ratings of 1/8 W, 1/4 W, 1/2 W, and 1 W. A 1/2-W resistor is able to safely dissipate 1/2 W of power, indefinitely. Resistors with larger power ratings are more expensive and bulkier than resistors with lower power ratings. Good engineering practice requires that resistor power ratings be specified to be as large as, but not larger than, necessary. The value of the current source current is i = 30 mA Specify the power rating for each resistor. R1 R₂ www ir = is Consider the circuit shown in Figure to the right. The values of the resistances are R₁ =100022, R₂ = 2000, and R₂ = 4000 R3 is
Question: We have more diodes out there, like for example, we have a diode which is called special-purpose diodes or special diodes. List at least 3 special diodes and answer the following. 1. Name of the Diode 2. Short Description 3. In your own opinion, without the use of the internet, where do you think you can use or apply that specific diode especially in the world of Computer Engineering.