4-) Using the DC (operating point) analysis of the following circuit, a) Find the operating point(s) of the terminal variables of the 3-terminal, b) Using the linear equivalent(s) of the 3-terminal, obtain all the possible small-signal equivalent circuits. c) Find the complete values of the voltage v2. R=3 N il iz ij=vi/3 iz-vi-6=0 E=6 V R3=2 2 V2 VI e(t)=0.2cos2t V E=8 V

4-) Using the DC (operating point) analysis of the following circuit, a) Find the operating point(s) of the terminal variables of the 3-terminal, b) Using the linear equivalent(s) of the 3-terminal, obtain all the possible small-signal equivalent circuits. c) Find the complete values of the voltage v2. R=3 N il iz ij=vi/3 iz-vi-6=0 E=6 V R3=2 2 V2 VI e(t)=0.2cos2t V E=8 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

10 k2, RE = R, = 150 2, r'e = 50 2, and Bac = 50. The For a common-emitter anmplifier, R value of the voltage gain is +Vcc Rc C3 R oVout REI R2 RE2 Select one: a. 67 b. 100 C. 50 d. 28.5
DC DC Converters a) A step-up PWM converter has the following data: V = 8 V, Vo = 24 V, lo = 1.25 A, and f = 200 kHz. Calculate the minimum inductance required for the converter operation in CCM (Continuous Current Mode). Then, determine the required capacitance for the converter. Assume n = 100 %. b) Design a boost SMPS converter to meet the following specifications: V = 80 V, Vo= 400 V, R. = 480 n, f.= 25 kHz, VNOS 1%. Find L, C, minimum inductor current lupin), maximum inductor current tunan), and output power. Then, sketch the inductor voitage and current waveforms for one cycle.
build an inverting summing amplifier with 2 inputs: a 1 V DC signal anda sine wave with an amplitude of 2 V and 1 kHz frequency.V Simulate for 2 msec
Q2) The buck-boost converter has parameter Vs = 12V, R = 10 N, L=10 µ H, C =20 µ F, and the switching frequency is 100 kHz. Sketch the inductor and capacitor currents for the converter when the time for diode Ton= 0.3 Toff.
i need the answer quickly
What output voltage results in the circuit below for an input of 0.5 V. Refer to the following for the values of Rf = 413981 ohms, R1 = 16788 ohms. Express your answer up to two decimal places. ... V. 360 kQ 12 ko Round your answer to 2 decimal places.
v(t) 20V -20V A laptop charger is connected with a load resistance R=47670 and practical PN junction diode is used as shown in Figure. Find the value of the output voltage in the positive half cycle |(in volts) if the input applied voltage is v(t)=20sin314t.
Prob 1: For each of the 8 circuits below, draw small signal model and calculate Vout/Vin. Vb1, Vb2 are dc voltage sources. and I1 is an ideal dc current source. Ignore body effect for all problems. Vino M3 M₂ M₁ (a) VDD J Vb₁ M3 (e) VDD VinM₂ Vb2M₁ Vb3 Vb2 - Vout Vb1 Vout HE Vout o Vb₁ VinM₂ 46! M3 (b) VDD B M₁ T. M3H (f) VDD VinM₁ M₂ Vout VinM₂ 4M₁ (c) M3 M3 VDD VDD 74 Vb1M₂ Vino M₁ (g) Vout Vout Vb1 Vb2 HE Vin VinM₂ M3 M3 VDD (d) HL M₁ M₁ -o Vout M2o Vout 1₁ (h) VDD
B- Let f(t) be the 2n- periodic function defined over the interval (-nt, A) by: [o if -n
(Boost de-dc converter with continuous inductor current. Evaluation of inductor and capacitor values) EX3: The boost converter shown bellow has the following specifications: Vin = de input voltage = 12 V, de output voltage = 30 V, output voltage peak-to-peak ripple = 1% Inductor current peak-to-peak ripple 10%, f;= switching frequency = 25 kHz and R = load resistance = 50 N Assuming that the converter is ideal, calculate: a) The duty cycle. b) The average input current. c) The minimum required inductance that ensures continuous inductor current. d) The required inductance so that peak-to-peak current ripple = 10%. e) The minimum and maximum values of the input current. f) The value of the output capacitor so that the output voltage ripple = 1%. g) Verify the theoretical results with the respective simulation ones. Boost inductor Output filter capacitor D VL 1R Vin S R Vo