4) The parallel circuit with three resistors connected to a voltage source (Vs) of 120 V. The resistor values are 15.8 0, 22.7 2, and 13.0 2 for R, R3, and R), respectively. a. Determine the equivalent resistance of the circuit. b. Determine the total current in the circuit. c. Determine the current in each branch resistor using current divider rule.

4) The parallel circuit with three resistors connected to a voltage source (Vs) of 120 V. The resistor values are 15.8 0, 22.7 2, and 13.0 2 for R, R3, and R), respectively. a. Determine the equivalent resistance of the circuit. b. Determine the total current in the circuit. c. Determine the current in each branch resistor using current divider rule.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

One of the resistors in this voltage divider circuit has failed (either open or shorted). Based on the voltage readings shown at each load, comparing what each load voltage is versus what it should be, determine which resistor has failed and what type of failure it is: - 50 V R₁ wwwww 30 R₁ w... R4 Load #1 Design voltage: -9 V Actual voltage: -31.7 V Load #2 Design voltage: -18.7 V Actual voltage: -33.8 V Load #3 Design voltage: -35.3 V Actual voltage: -41.1 V
Voltage sources in series Select one: a. When two or more voltage sources are connected in parallel, the total voltage equals to the sum of all individual voltage sources b. When two or more current sources are connected in parallel, the total current equals to the sum of all individual current sources C. When two or more current sources are connected in series, the total voltage equals to the sum of all individual voltage sources d. None of the answers e. When two or more voltage sources are connected in series, the total voltage equals to the sum of all individual voltage sources OO Shot by Hisense H12
The voltage divider rule states that: Select one: a. None of the answers. b. the current passing to a series resistive circuit will be dropped across all resistors in proportion to the magnitude of the individual resistors. C. the voltage applied to a parallel resistive circuit will be dropped across all resistors in proportion to the magnitude of the individual resistors. d. the voltage applied to a series resistive circuit will be dropped across all resistors in proportion to the magnitude of the individual resistors. OE Shot by Hisense H12
Now, double the value of R1 and R2. Disconnect the load and make sure that VNL (No Load) is the same as the original circuit. Then repeat the VOUT measurements for load values of 50 Ohm and 500 Ohm. Was the loaded voltage divider more stable or less stable than the original circuit? (In the book it provides the current values but in the problem it provides no current ranges) This relates to voltage divider stability. I think its asking me to compare the stability of the No Load circuit with the Resistor Load circuit.
Current sources in parallel Select one: a. When two or more voltage sources are connected in series, the total voltage equals to the sum of all individual voltage sources b. When two or more current sources are connected in series, the total current equals to the sum of all individual current sources c. None of the answers d. When two or more current sources are connected in parallel, the total current equals to the sum of all individual current sources e. When two or more voltage sources are connected in parallel, the total current equals to the sum of all individual current sources
A series circuit consists of a 240-V source and 12-ohm, 20- ohm, and 16-ohm resistors. a. Find the current (Amp) out of the positive terminal of the voltage source. b. Use voltage divider rule to find voltage (Volt) across the 16-ohm resistor.
2. Three resistors R1, R2 and R3 are connected in series parallel with R1 in series with parallel combination of R2 and R3. The whole combination is connected across a 120V DC source. Resistors R1, R2 and R3 takes 750 w, 250 W and 200 W, respectively. Calculate the resistance R2. Why are street lights connected in parallel and not in series, explain.
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
Q6
Sol with diagram
Explain why
2. From the figure, when the voltage V2 is 10 and 10 volts, the total voltage VD4 and VD6 is 0.7 volts. The voltage VD5 is 0.3 volts. The resistances R4, R5 and R6 are 9 5.1 and 15.1 ohms accordingly. Sequence Show how to calculate and answer the questions in the box. empty as follows D4 A D5 D6 R4 V2 R5 R6 When V2 equals 10 Volts 2.2 When V2 is equal to -10 Volts i Current flow through D4 : Answer.... : Current value Flow through D4 : Answer... .: Current flow through D5 : Answer.. Krahok fee stream flowing through D5 : Answer.. Current flow through D6 : Answer.. Current value Flow through D6 : Answer.... Current flow through R4 : Answer.. Current value Flow through R4 : Answer.... Current flow through R5 : Answer.. . Current value Flow through R5: Answer Current flow through R6 : Answer.. Current value Flow through R6 : Answer.... Current source V2 : Answer.. Current value Power supply V2 : Answer..