(4) The Am1004-T61 magnesium tube is reinforced with the bonded A-36 steel rod. If the allowable shear stresses for the magnesium and steel are (Tallow)mg = 45 MPa and (Tallow)st = 80 MPa, respectively, determine the maximum torque T that can be applied at A. Additionally, find the corresponding angle of twist of end A. 900 mm 80 mm, T - 40 mm

Q: Q1: A torque T=4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa. Determine: (a) maximum…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: Determine the maximum torque T in kN-m without exceeding a shear stre of 70 MPa In steel and 50 MPa…

A: 1. 10.44kn-m

Q: Trusses 1. Find the stresses of FAB, FAC, FBC & FBD- ( 20k 15k 60 60 Ra Rb

A: This question belongs to subject structural analysis. In this question find out stresses in members…

Q: Q.1/The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A:

Q: Problem 3 in the steel structure shown, a 6-mm-diamter pin is used at D and 10-mm-diameter pins are…

A:

Q: NS 5 ft iG B 920 lb 1145 lb 1760 lb -20 ft20 ft 20 t 20 -20120 t-

A: To find the force in member CD , ND and NK -

Q: Determine the smallest safe cross-sectional areas of members CD, CI and CH for the truss shown. The…

A:

Q: 1. The aluminum rod AB (Ga = 27 GPa) is bonded to the brass rod BD (Gpr = 39 GPa). The portion CD of…

A:

Q: In the structure shown, in diameter pins are used at A, B&D The ultimate shearing stress for the pin…

A: Diameter -  ϕpin = 13in   Ultimate shearing stress -  At point D -  σD = 6ksi  At AB -  σAB = 10 ksi

Q: A solid shaft of circular cross-section is subjected to torque Twhich produces a maximum shear…

A:

Q: D CED Front view 18 mm 6 mm B B Side view 160 mm 120 mm A Top view In the steel structure shown, a…

A:

Q: Auniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P-7…

A: Determine the axial deformation of uniform bar 1 in mm

Q: The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). Solve the…

A: The load =PThe load in wire BD =P1The load in wire CE =P2The length of beam =7mThe wire BD is 3m…

Q: Q.1//The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A: to find stress in each rod

Q: 022 Plate 3-Method of Consistent Deformation Determine the force in member CD of the truss shown in…

A:

Q: 3. SOLVE FOR THE REACTIONS OF THE TRUSS SHOWN BELOW: P B -2m -2m- D P -2m- -2m- E P -2m- Assume P =…

A:

Q: 4.1 The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD…

A:

Q: The pin-connected structure shown consists of a rigid bar ABCD and two axial members. Bar (1) is…

A:

Q: The mechanical system consists of two identical steel rods (A = 30 mm?, E = 200GPa, a = 15×106/°C)…

A:

Q: The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed…

A:

Q: 15 Flad the ABE GO Kri CD = 70 ksi BC - 50 ksi 0.4 in2 4. 0.3 n? 4P- 3p P4

A:

Q: A W18x40 standard steel shape is used to support the loads shown on the beam. Assume P= 26 kips, w =…

A:

Q: Compute the shearing stress in the pin at B for the member supported as shown. The pin diameter is…

A:

Q: LBC LAB

A:

Q: A tension member consists of a 50-mm-diameter brass (E = 100 GPa) bar connected to a 32-mm-diameter…

A: Given data : Tensile load (P)=50 KNBrass Diameter of brass (dB)=50 mmLength (LB)=1.5 mModulus of…

Q: 1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used…

A:

Q: The aluminum rod AB GPa) iš bondéd tỏ tó the brass rod BD (G = 39 GPa). Knowing that portion CD of…

A:

Q: The safety stress for the steel bar shown in the figure is σallow= 160MPa. According to the greatest…

A: Solution:

Q: In the steel structure shown, a 6-mm-diameter pin is used at Cand 10-mm-diameter pins are used at…

A: To find value of load P

Q: 3. SOLVE FOR THE REACTIONS OF THE TRUSS SHOWN BELOW: P B -2m -2m- D P -2m- -2m- E P -2m 2m

A:

Q: 100kN B (EA is constant) A 60KN + Determine the Force in member 4m D BD) se Force method (Consistent…

A:

Q: cmonl *9-56. The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and…

A:

Q: Detemine the magnitude of the average normal stress in member AB when T,35C Express your answer to…

A: This problem is related to stress and strain theory from strength of material. In this problem given…

Q: Cm 4m 4m Gom G Gm. F Gm 76 KN 14 76 KN

A:

Q: J- A T beam supports the three concentrated loads shawn. Öctermine the merximum tensile 1.41 KN 5.64…

A:

Q: Compute the total deformation (in mm) of the tapered square steel bar caused by the 30-kN axial…

A:

Q: A 120 KN L= 4m A = 0-04 nt E>200 Gla t. L=6m A=0:06m 90KN E-80G7P4

A:

Types and properties of steel

Steel is an alloy of iron. It is formed by heating iron and combining carbon (0.1-1.7%) with it and minor amounts of other elements such sulfur,  chromium, manganese, nickel, etc. Thousands of steel grades have been published, registered, or regulated around the world, each with its chemical composition, and special numbering systems have been devised in various countries to classify the vast number of alloys.