4) The 54 kg crate rests on a 27 kg slender350 mm-xbar which is simply supported at point 0. Ifthe mass centers of the bar and the crate areG1 and G2 respectively, determine the tensionG2300 mmforce in cable AB and the reaction forces atOpoint 0.|G1240 mm70 mm

Given: Weight of the crate (WC)=54×9.81=529.74NWeight of the slender bar (Wb)=27×9.81=264.87N

4) The 54 kg crate rests on a 27 kg slender 350 mm bar which is simply supported at point 0. If B| the mass centers of the bar and the crate are G, and G2 respectively, determine the tension G2 |300 mm force in cable AB and the reaction forces at point 0. |G1 240 mm 70 mm

4) The 54 kg crate rests on a 27 kg slender 350 mm bar which is simply supported at point 0. If B| the mass centers of the bar and the crate are G, and G2 respectively, determine the tension G2 |300 mm force in cable AB and the reaction forces at point 0. |G1 240 mm 70 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.26P: The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A...

See similar textbooks

Related questions

Q: The bars AB and AC are joined by a pin at A and a horizontal cable. The vertical cable carrying the…

A: Given: The load, P = 100 kN

Q: If the cart's mass is 32 kg and it is subjected to a horizontal force of P-90 N. determine the…

Q: PROBLEM 3.Rod XY and smooth surface O hold the 1600-N cylinder in equilibrium as shown. Find the…

A: Given data W=1600 Nθ1=25°θ2=55°

Q: A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind…

A: According to the given data Reaction at wheel;m and road is 4200 N We need to find Determine the…

Q: A 415 kg safe is hanging from the apparatus below. Determine the tension in the cable. Dimension…

Q: A container of mass m = 120 kg is supported by three cables as shown. Draw the free-body diagram…

A: To determine the tension in each cable, take all forces on point A and draw free body diagram

Q: Masses M1 and M2 are held on the frictionless inclined plane by a rigid inextensible bar of length l…

A: The free-diagram is shown in the figure below.

Q: The line of action of the 3480-lb force runs through the points A and B as shown in the figure.…

A: 1) The line of action of the 3480-lb force runs through the points A and B as shown in the…

Q: The force P on the handle of the positioning lever produces a vertical compression of 56 lb in the…

A: Given that , a=3.4 in b=8.6 in

Q: The homogeneous 200-lb sign is suspended from three wires. Find the tension in each wire.

A: Weight is 200lb sinθ=45 cosθ=35. ∑Fy=0 T1 is completely horizontal and Due to symmetry T2=100 lb…

Q: The Free-Body diagram for joint C is drawn assuming that all internal forces are in tension. Solve…

A: Given:Load acting at point D, P=2660 N

Q: 8. The 100 lb "slider" C is held in place on the smooth bar by the cable AC. Determine the tension…

A: The weight of the slider is = 100lb

Q: PROBLEM 3.Rod XY and smooth surface O hold the 1600-N cylinder in equilibrium as shown. Find the…

A: Solution: The free body diagram of the cylinder is shown below

Q: The uniform rectangular panel ABCD has a mass of 33 kg and is hinged at its corners A and B to the…

A: Given Mass = 33 kg To find Magnitude of T and B

Q: The shear leg derrick is used to haul the 150-kg net of fish onto the dock. Determine the…

Q: The uniform 21-m pole has a mass of 115 kg and is supported by its smooth ends against the vertical…

A: As per given question Length of rod =21m Weight =115kg We have to determine reaction at A and B

Q: The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240…

A: Consider the free body diagram shown below for the given system.

Q: Q3 - The uniform bar OC of length L and mass (m ) pivots freely about a horizontal axis through O.…

A: Given data: The angle between OAC is θ=45° The length of the bar is L

Q: End B of the uniform 2.7-kg bar AB is connected to a small roller that moves in a horizontal slot.…

A: The stiffness of spring is k=58 N/m The free length of the spring li=0.3 m The mass of the disc is…

Q: member AB of the frame. In other words, find the reactions at pins A and B. 300 lb 60° B 4 ft E -3…

Question

4) The 54 kg crate rests on a 27 kg slender
350 mm
-x
bar which is simply supported at point 0. If
the mass centers of the bar and the crate are
G1 and G2 respectively, determine the tension
G2
300 mm
force in cable AB and the reaction forces at
O
point 0.
|G1
240 mm
70 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the tension in the cable at B, given that the uniform cylinder weighs 350 lb. Neglect friction and the weight of bar AB.
Q1/ The 500-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the support point O. The x-y plane is vertical. 30° 15 kN-m 3 kN C 1.4 kN 1.2 m- 1.8 m 1.8 m Q2/ A former student of mechanics wishes to weigh himself but has access only to a scale A with capacity limited to 100 lb and a small 20-lb spring dynamometer B. With the rig shown he discovers that when he exerts a pull on the rope so that B registers 19 lb, the scale A reads 67 lb. What is his correct weight? Q3/ When the 0.05-kg body is in the position shown, the linear spring is stretched 10 mm. Determine the force P required to break contact at C. Complete solutions for (a) including the effects of the weight and (b) neglecting the weight. P 60 mm 60 mm A 40 mm B www k = 1750 N/m 40 mm
L from Pivot 1. A uniform bar with mass M =3.25 kilograms is the top end of the bar. A cable connects to the bar as shown in the diagram. the 75.0 40.0° a. Calculate the tension in the cable required to keep tne bar in static equilibrium. Pivot preso your your answe stem right when n terr b. Calculate the force (both magnitude and direction) exerted by the pivot.
The wheels, axle, and handles of a wheelbarrow W=62N. The load chamber and its contents weigh Wl=575N. The drawing chose leave to Forsyth and different wheelbarrow designs to support the wheelbarrow and equilibrium the man's hands apply a force to the handles that is directly vertically upward. consider the rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the Man's force for both designs
Clear and complete solution please thank you
The weight of the limb is W=15 lbs.The contact of foot with the ground can be modeled as a pin/hinge here. Determine the reaction force of the ground and the reaction at the knee joint and its direction/angle θ. Note: use the thee force member condition to find the angle of FK.Q4.As it’s been shown in the below figure,a person is using an exercise machine. Points A and B correspond to the shoulder and elbow joints, respectively. Relative to the person, the upper arm (AB) is extended toward the left (x-direction) and the lower arm (BC) is extended forward (z-direction). At this instant, the person is holding a handle that is connected by a cable to a suspending weight. The weight applies an upward (in the y-direction) force with magnitude F on the arm at point C. The lengths of the upper arm and lower arm are AB̅̅̅̅= 20cm and BC̅̅̅̅= 25cm, respectively, and the magnitude of the applied force is F = 400 N.Determine the components of reaction developed at the shoulder joint A When the…
Current Attempt in Progress In the special position shown for the log hoist, booms AF and EG are at right angles to one another and AF is perpendicular to AB. If the hoist is handling a log weighing 4380 lb, compute the magnitudes of the forces supported by the pins at A and D in this one position due to the weight of the log. 50° A = Answers: i D= i 15" A 13' 26" B eTextbook and Media E C lb lb R 10" 3' -"( 14' G
The structure is made of the light bar AB and the 50-kg uniform bar CD. Compute the magnitude of the forces acting on the pins at A and D. B 800 N 3 m 3 m D 2 m
Calculate the tension T in the cable which supports the 1000-lb load with the pulley arrangement shown. Each pulley is free to rotate about its bearing, and the weights of all parts are small compared with the load. Find the magni- tude of the total force on the bearing of pulley C. 8=30° Joel 1000 lb
A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind member CD. The normal force due to contact between the wheel and the road is 4200 N. Assume the weight of the wheel and suspension system components is negligible. Determine the magnitude of the member CD. Is the member in tension or compression? Determine the support reactions at A. Determine the unstretched length of the spring EF given a spring constant of 150 kN/m.
The machine shown is used to help load luggage into airliners. The combined mass of the conveyor and luggage is 110 kg with mass center at G. Determine and plot the force in the hydruaulic cylinder BC (report your answer as a positive value) as a function of over the range 5° 0 ≤ 36°, then answer the questions. Assume DE = 2070 mm, CD = 1280 mm, c = 1680 mm, d = 1130 mm, e = 570 mm, f = 2380 mm. t Questions: E B i D If 0 = 11°, BC = If 0 = 21°, BC = i Over this range, the maximum value for BC = i N N N and occurs when 8 =
4. Determine the tension in the cable at B, given that the uniform cylinder weighs 350 lb. Neglect friction and the weight of bar AB.