4) Sketch the free body diagram for the motor blower assembly shown below. Show the torques at the inputs and outputs to the various components. Solve the reaction forces at the bolt supports of the gear box. The gearbox weighs 50 lbs with a center of gravity between the two mounts. Motor 1 hp 1800 rpm Gear box Direction of rotation Blower 6000 rpm

4) Sketch the free body diagram for the motor blower assembly shown below. Show the torques at the inputs and outputs to the various components. Solve the reaction forces at the bolt supports of the gear box. The gearbox weighs 50 lbs with a center of gravity between the two mounts. Motor 1 hp 1800 rpm Gear box Direction of rotation Blower 6000 rpm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The following drive system is used to raise a load at constant velocity. The motor rotational speed…

A: (1) Moment of inertia of drum about the output axis, Therefore, Mass of drum is 24 kg. Distance…

Q: 2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20…

Q: Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and…

A: The diameter of the smallest pulley = 2 in. Thus the maximum speed will be maximum at this pulley.…

Q: A belt transmission system is shown as shown in the picture. Pulley A transmits torque 1,150 lb-in.…

Q: The bevel gear train shown is called Humpage's reduction gears. The input is to gear 2, and the…

A: The ratio of teeth on driven gears to the teeth on the driver gears for a gear train is termed as…

Q: Q4:- Two mating gear wheels have 18 and 36 teeth of 10 mm module and 20° pressure angle. Determine…

A: Given: t=18T=36m=10 mmϕ=20°

Q: Chains and belts behave similarly except that chains often have zero tension on the sldCk sume…

Q: Q5/ The wheel of mutor Cycle and the engine parts have antoment of inertia 2-5 kg.m? and o15 kg.m?…

Q: Two gears (A and B) are in mesh (they are interlocked) and both spin around their centers of…

Q: 4. A machine shaft turning at 600 rpm is supported on bearings 30" apart. Twenty HP is supplied to…

Q: 7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative…

A: (a) Write the given data. Tf=48Df=10.5 inTs1=30Ts2=26Ts3=23Ts4=20Ts5=16Ts6=12Nf=105 rpmFf=28 lb

Q: In an open belt drive, two sheaves have diameters of 5 in. and 12 in. Determine the center distance…

A: Write the given data with suitable variables: d1=12 ind2=5 inL=72 in

Q: For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each…

A: The objective of the question is to analyze the capabilities of a gearbox in a hot strip mill. This…

Q: The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating…

A: For the solution refer below images.

Q: The power and motion can be transmitted from one shaft to another shaft by means of gear drives if…

A: To transfer power and motion from one shaft to another shaft when the centre distance between the…

Q: The figure below shows the components of normal forces, the value of radial force on the gear wheel…

Q: Draw free-body diagrams of the two gears, assuming an input couple M on the OUT X shaft of the…

A: For the gear on shaft AB, For the gear on shaft CD

Q: What are the necessary and sufficient requirements for the two stage gearbox to mesh properly for…

Q: 5. For the engine-transmission-propeller problem shown below, The engine generates a torque of…

A: Transmission ratio,

Q: 2. A machine shaft turning at 600 rpm is supported on bearings 20" apart. Twenty HP is supplied to…

Q: hat is torque produced by the crank of the engine if the tangential force is 10 N and

A: Given:Tangential force, F=10 Ncrank radius, r=0.2 m

Q: The power and motion cannot be transmitted from one shaft to another shaft by means of gear drives…

Q: 3. Figure 4 shows a simplified schematic of the drive system of joint 4 of the PUMA 560. The…

A: Given Total coupling stiffness = 200 Nt m/rad Shaft stiffness = 400 Nt m/rad Output stiffness = 2000…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

4) Sketch the free body diagram for the motor blower assembly shown below. Show the torques at the
inputs and outputs to the various components. Solve the reaction forces at the bolt supports of the
gear box. The gearbox weighs 50 lbs with a center of gravity between the two mounts.
Motor
1 hp
1800 rpm
10 in.
Gear box
Direction
of rotation
Blower
6000 rpm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Solution

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw free-body diagrams of the two gears, assuming an input couple M on theOUT X shaft of the larger gear in the direction shown. Include forces at bearings A, B, D and E. M isthe reaction couple at the output shaft - i.e. the resistance to turning of the object being driven.The gears have 48 and 24 teeth respectively. If the input gear (large gear) turns at 100 rpm(= revolutions per minute), the output speed (small gear) is _______rpm.Wil OUT X IN Xl M be larger or smaller than M ?
2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X
5. For the engine-transmission-propeller problem shown below, The engine generates a torque of 219lb-ft, and it is bolted to a frame at locations A and B. The transmission reverses the rotation direction. The transmission ratio is 1.5 (i.e. the propeller speed is -1/1.5 the engine speed, the minus sign indicates the change in direction). d. Sketch the free body diagram. Be sure to show the torques at the input and outputs to the different components. Note the change in the rotation direction between the engine and shaft. e. Solve for the reaction forces at the bolt supports of the engine, if the distance between them is 1 ft. Propeller Engine Reduction ratio 1.5 Engine is attached B
Hello, Could you please help with the question attached or give guidance please, thnk you
For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each driven by a DC motor of 10,500 HP operating at 125 RPM. For your ASSIGNED gearbox only, you are required to analyze the gearbox capabilities by doing thefollowing: 1. Calculate the maximum motor torque2. calculate the force transmitted by the gearing.3. Using statics, calculate the equivalent radial load at the bearings for BOTH the pinion shaft and the gear shaft. (Four bearings total; two per shaft). Include FBDs of the shafts.4. Research the load capacities for the bearings.(Hint: the bearing manufacturer is most likely Timken / Torrington).5. Calculate the expected bearing life for each bearing.6. Calculate the safety factor for both the bending strength and the pitting resistance for the pinion shaft AND the gear shaft gear teeth based on the transmitted load and the gear material(s).7. Draw the shear, bending moment, and torque diagrams for the GEAR SHAFT ONLY.8. Calculate the…
3. Figure 4 shows a simplified schematic of the drive system of joint 4 of the PUMA 560. The torsional stiffness of the couplings is 200 Nt-m/radian each, that of the shaft is 400 Nt-m/radian, and each of the reduction gear pairs has been measured to have output stiffness of 2000 Nt-m/radian with its input gears fixed. Both the first and second reductions have n=4. Assuming the structure and bearing are perfectly rigid, a) What is the effective stiffness of gear 1 if the electric motor's shaft is locked? b) What is the effective stiffness of gear 3 if the electric motor's shaft is locked? c) What is the stiffness of the joint (i.e., when the motor's shaft is locked)? In other words, find out the effective stiffness of the output gear 4. - Electric motor -#1 Coupling Connecting rod #2 Coupling -#1 Gear 42 Gear #3 Gear - #4 Gear Figure 4: Simplified version of the driven train of joint 4 of PUMA 560.
A belt conveyor transports 18 tonnes per hr at 20°. Determine the unit weight of belt material in kg/ply-cm width-m to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
Qs1 The wheel of metor Cy cle and the engine parts have anoment of inertia 2-5 kg.m? and o 15 kg.m? respectively The axis of rotation of the engine erank Shaft is parallel to that of the road whels-If the gear ratio is 5:1 and the diameter of the read wheels is o.65 m, find the magnitude and direction of the gyroscopic Couple when the motor Cycle rounds a eurve of 3om radius at 16 m/s.
Hi, could you please help with the following question please thank you
The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating at a speed of 1200 revolutions per minute. It must increase the torque received at its input shaft 16 times. Spur gears with 20° pressure angle should be used. Input and output shafts should be aligned. The transmission should take up as little space as possible. The distance between the centers of the input shaft and the intermediate shaft (the one that loads gears 3 and 4) should be 10 inches. Determine the magnitude of the radial load that gear 4 exerts on gear 4. Write your answer in pounds.
P5/ The wheel of metor Cycle and the engine parts have antoment of inertia 2-5 kg.m? and o 15 Kg.m² respectively The axis of rotation of the engine erank Shaft is parallel to that of the road wheels-If the gear ratio is 5:1 and the diameter o f the read whels is o.65 m, find the magnitude and direction of the gyroscopic Couple when the motor Cycle rounds a eurve of Bom radius at l6 m/s.
Do it fast plz 2 upvote will be given damn sure