4 4) Consider the following system:Y(s)X(s)H,(s)H,(s)H,(s) =H2(s) = 2andWhere(s+2)(s+a)a) Determine the parameters "a" andsuch that the overall transfer function isH(s) =(s+4)(s+5)b) Determine the output y(t) of the system with the above transfer function to the unit step inputx(t)=u(t).

4) Consider the following system: Y(s) X(s) H,(s) H,(s) H, (s) = and H2(s) = Where (s+2)(s+a) a) Determine the parameters "a" and "b" such that the overall transfer function is H(s) = %3D (s+4)(s+5) b) Determine the output y(t) of the system with the above transfer function to the unit step input x(t)=u[t).

4) Consider the following system: Y(s) X(s) H,(s) H,(s) H, (s) = and H2(s) = Where (s+2)(s+a) a) Determine the parameters "a" and "b" such that the overall transfer function is H(s) = %3D (s+4)(s+5) b) Determine the output y(t) of the system with the above transfer function to the unit step input x(t)=u[t).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Must answer both. Dont say only one will be answered.
Classify the transfer function to proper and improper. Plot the s-plane and find the system stability.
For the system given in figure below, the transfer function C(s)/ U(s) is
Reduce the block diagram shown in the Figure below and determine the transfer function ?0(s) / V1(s)
1. Simplify the block diagram shown in Figure 1.. Obtain the transfer function relating C(s) and R(s). R(s) X(s) G2 C(s)
Help me with transfer function problem. Please show all the steps (Mention Step 1 ,2... in your handwritten solution)
I will appreciated if someone can explain step by step this problem.
The transfer function is H(s) = (1.2s+0.18)/(s3 + 0.74s2 + 0.92s) and C(s) = (K(s+1))/ s A) A disturbance input W(s) =W/sk , where W is a constant, into the feedbackcontroller as shown below. We set R(s) = 0. What type of disturbance input W(s)(step, ramp, or parabola) can thesystem reject (i.e., the steady-state error ess is a nonzero constant)? (B) Suppose you want to design the controller C(s) to produce a closed-loop response to areference step input that has no more than 30% maximum overshoot (Mp ≤ 0.30) and a peak timeof no more than 8 sec (tp ≤ 8). Given the specifications on Mp and tp , compute the constraintson the damping ratio ζ and the damped natural frequency ω, assuming that the closed-loop systemis approximated as a 2nd-order underdamped system. Sketch the allowable regions in thecomplex plane (the s-plane) that these constraints define, and shade in the regions where the polesshould not be placed.
Reduce the following block diagrams to a single transfer function output/input.
Find the transfer function T (s) for the circuit shown in figure below. CAI RAI RBI Vin o Vo CBI R1 R2 Stay
Find the transfer function T(s) for the circuit shown in figure below. CAI RAI RB1 Vin o Vo CBL R1 R2
Question about control systems engineering. Thank you in advance.