Could I get a a detailed explanation for question 4 and 5. You can make 10 more submissions for this question.5) Cp =J/K SubmitYou currently have 0 submissions for this question. OnlYou can make 10 more submissions for this question. The heat capacity of a certain amount of a particular gas at constant pressure is greater than that at constant volume by91.7 J/K.1) (a) How many moles of the gas are there?11.029mol SubmitYou currently have 1 submissions for this question. Only 10 submission are allowed.You can make 9 more submissions for this question.2)(b) If the gas is monatomic, what are C, and Cp?Cv=136.86J/K Submit 4You currently have 1 submissions for this question. Only 10 submission are allowed.You can make 9 more submissions for this question.3) Cp=228.5J/K SubmitYou currently have 1 submissions for this question. Only 10 submission are allowed.You can make 9 more submissions for this question.4) (c) If the gas consists of diatomic molecules that rotate but do not vibrate, what are Cy and Cp? Cv =J/K SubmitYou currently have 0 submissions for this question. Only 10 submission are allowed.You can make 10 more submissions for this question.+

Answered: Image /qna-images/answer/a08ad51e-595c-4662-8a87-a2fb6e078eb3.jpg

Answered: 4) (c) If the gas consists of diatomic…

Similar questions

Hello, I was trying to solve just the first three. Thank you very much!
Is there any simpler solution to this? Without having to calculate so many variables?
(Please refer to Fig. 1) W = FAx (Equation 1) F = qE (Equation 2) APEelec = -W (Equation 3) Substituting Eq. 1 in Eq. 3, APE elec Then subs. Eq. 2 in Eq. 4, 4. What does q means in the derived equation? = -FAx (Equation 4) APE etec = -qEAx (Eq. 2.1) Which is what we need to derive.
does not depend on is linearly proportional to is inversely proportional to increases by a factor of 2 decreases by a factor of 2 does not change The capacitor charge its capacitance. Therefore, if the potential difference does not change and capacitance decreases twice, the charge Q
solve 2c using engineering notation
Could you possibly include a picture of the written solution, the transcription gets a bit confusing! Thank you :)
Using your values for 7, calculate the average period Ibar (I) and its standard error. How does the error on the average period /bar (T) compares to the errors on the periods, I? What can you do to reduce the uncertainty on /bar (T)? What can you do to reduce the uncertainty on 7 ? Peried Trial T AT 4 141 $ 10.69 +α-0.5 2 10.60 + or -0.5 2 10.40 +α-0.5 10.43 +α-0.5 S 10.37 + or -0.5 Using your values for T, calculate the average period 7 and its standard error How does the error on the garage period compares to the errors on the periods, 7? What can you do to reduce the uncertainty on 7? What can you do to reduce the uncertainty on T7
This sheet is not actually being graded. It's just a test review. I need help with 3-5.
Hello, I have a physics assignment and wanted to get help with the answers. I was told to repost the question to get the remaining sub parts done. I accidentally posted a photo a few minutes ago without the instructions I just need the bottom four completed.
please answer parts E, F, and G
The length of cell A is 9×10^6 m. The length of cell B is 0.0000003 m. What is the ratio of cell A's length to cell B's length? Use pencil and paper. Is it easier to find the ratio when the numbers are expressed in scientific notation or in standard form? Explain your reasoning.
An ant is crawling along a straight wire, which we shall call the z axis, from A to B to C to D (which overlaps A), as shown in the figure below. (Figure 1) O is the origin. Suppose you take measurements and find that AB is 44 cm, BC is 20 cm,and AO is 4 cm

SEE MORE QUESTIONS

4) (c) If the gas consists of diatomic molecules that rotate but do not vibrate, what are Cy and Cp? Cy= J/K Submit You currently have 0 submissions for this question. Only 10 submission are allowed. You can make 10 more submissions for this question.