- 4 An angle bracket having thickness t 20 mm is attached to the flange of a column by two 16-mm- diameter bolts as shown in Figure S01-7152. A uniformly distributed load from a floor joist acts on the top face of the bracket with a pressure p = 1900 kPa. The top face of the bracket has length L = 200 mm and width b = 75 mm. 25. Determine the average bearing pressure between the angle bracket and the bolts, in MPa. A. 48.7 bell C. 40.1 B. 50.2 D. 44.5 26. Determine the average shear stress in the bolts in MPa. (Disregard friction between the bracket and the column.) A. 76.32 C. 65.47 B. 60.89 D. 70.87 and stan mulos fest .8 Distributed pressure on angle bracket Floor slab 10000 WHITE Ho Angle bracket Floor joist Angle bracket

- 4 An angle bracket having thickness t 20 mm is attached to the flange of a column by two 16-mm- diameter bolts as shown in Figure S01-7152. A uniformly distributed load from a floor joist acts on the top face of the bracket with a pressure p = 1900 kPa. The top face of the bracket has length L = 200 mm and width b = 75 mm. 25. Determine the average bearing pressure between the angle bracket and the bolts, in MPa. A. 48.7 bell C. 40.1 B. 50.2 D. 44.5 26. Determine the average shear stress in the bolts in MPa. (Disregard friction between the bracket and the column.) A. 76.32 C. 65.47 B. 60.89 D. 70.87 and stan mulos fest .8 Distributed pressure on angle bracket Floor slab 10000 WHITE Ho Angle bracket Floor joist Angle bracket

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Quiz/ find the angle of rotation of the free end for the beam shown, then find the max sheaving stress If you know GAI = 28 GN/m² Gst=83 GN1m² GBV = 35 GN/m² Aluminum steel Bronzer Do d=100mm 3m d=75mm 2m 1.5m 1.5 KN.m
WELDED CONNECTIONS: THE BRACKET SHOWN IN THE FIGURE IS WELDED ON ONE SIDE OF A STEEL COLUMN WITH 800 mm OF 6 mm FILLET WELD. DETERMINE THE MAXIMUM SHEAR STRESS ON THE WELD.
The one end of a hollow square bar whose side is 10 with 1 thickness is under a tensile stress 102500 and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σall =243000 psi for pin material.
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
Please answer the questions on the picture and draw free-body diagram make sure you show all of your work, Thank you for your help!
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 L3=1350 GPa. L2=2150 A L1 E Dia. 1 L1=1350 Р3-25 P1 L2 Dia. 2 P2=40 P2 P1=105 Dia2=45 L3 P3 D D 35 mm o Dia1=60
I Review Part A The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.035 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. µA T = 3.7216 Units Figure Pearson
3. Determine maximum strength P for the bracket connection in the figure. ST37 steel is used for the connection, F = 2400kg /cm,F, = 3700kg /cm %3D %3D IPE200 15 cm P=? PL 250x150x15 mm te 7 mm, L=250 mm
CE 1
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.
Answer 15&16